Precision Digital Corporation PD765-6X0-00 Instruction Manual Download Page 31

Page: 31 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

Setting the Decimal Point (

dc.pt

)

Decimal point for process inputs may be set with up to three decimal
places or with no decimal point at all.
Decimal point for RTD inputs may be set with 1 decimal place or none.
Decimal point for thermocouple inputs is fixed.
Pressing the

arrow moves the decimal point one place to the right

until no decimal point is displayed, it then moves to the leftmost position.

Setting the Temperature Scale (

F C

)

The meter can be set to display temperature in degrees Fahrenheit or
Celsius.
Press

arrow to change selection.

Press

Enter/Ack

to accept.

dec.p

dddd

Select Decimal

Point

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for PD765-6X0-00








































































Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands

Precision Digital Corporation PD765-6X0-00, Instruction Manual

Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands