Precision Digital Corporation PD765-6X0-00 Instruction Manual Download Page 3

Page: 3 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

ORDERING INFORMATION

Trident

85-265 VAC
Model

12-36 VDC
Model

Options Installed

PD765-6R0-00 PD765-7R0-00 No

options

PD765-6R0-10

24 V transmitter supply

PD765-6R2-00 PD765-7R2-00 2

relays

PD765-6R2-10

2 relays & 24 V transmitter supply

PD765-6R3-00 PD765-7R3-00 4-20

output

PD765-6R3-10

4-20 mA output & 24 V supply

PD765-6R3-20

4-20 mA output & dual 24 V supplies

PD765-7R5-00

2 relays & 4-20 mA output

PD765-6R5-10

2 relays, 4-20 mA output, & 24 V supply

Trident X2

85-265 VAC
Model

12-36 VDC
Model

Options Installed

PD765-6X0-00 PD765-7X0-00 No

options

PD765-6X0-10

24 V transmitter supply

PD765-6X2-00 PD765-7X2-00 2

relays

PD765-6X2-10

2 relays & 24 V transmitter supply

PD765-6X3-00 PD765-7X3-00 4-20

output

PD765-6X3-10

4-20 mA output & 24 V supply

PD765-6X3-20

4-20 mA output & dual 24 V supplies

PD765-7X5-00

2 relays & 4-20 mA output

PD765-6X5-10

2 relays, 4-20 mA output, & 24 V supply

Accessories

Model Description

PDA7232

RS-232 serial adapter with PDA7420 included

PDA7420

Trident meter copy cable, 7' (2.1 m)

PDA7422

RS-485 serial adapter with PDA7420 included

PDA7485-I

RS-232 to RS-485 isolated converter

PDA7485-N

RS-232 to RS-485 non-isolated converter

PDA8485-I

USB to RS-422/485 isolated converter

PDA8485-N

USB to RS-422/485 non-isolated converter

PDA8006

USB Serial Adapter

MeterView

Free

MeterView

software download at www.predig.com

Enclosures

NEMA 4 & explosion-proof enclosures – See Web site.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for PD765-6X0-00








































































Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands

Precision Digital Corporation PD765-6X0-00, Instruction Manual

Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands