Precision Digital Corporation PD765-6X0-00 Instruction Manual Download Page 49

Page: 49 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

Setting Up the Password (

pass

)

The

Password

menu is used to program a four-digit password to pre-

vent unauthorized changes to the programmed parameter settings.

Locking the Meter

Enter the

Password

menu and program a four-digit password.

For instructions on how to program numeric values see Setting Numeric
Values, page 28.

Record the password for future reference. If appropriate, it may be rec-
orded in the space provided.

Model:

Serial Number:
Password:

__ __ __ __

Unlocking the Meter

If the meter is password protected, the correct password must be en-
tered in order to make changes to the parameter settings.

pass

unlC

000

Program

Password

loCd

Run Mode

pass

loCd

000

Enter

Password

unlC

Run Mode

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for PD765-6X0-00








































































Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands

Precision Digital Corporation PD765-6X0-00, Instruction Manual

Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands