Precision Digital Corporation PD765-6X0-00 Instruction Manual Download Page 10 | Manualshive

Page: 10 / 71

background image

Trident Model PD765 Universal Input Meter Instruction Manual

10

Relays Option

RATING

2 SPDT (Form C); rated 3 A @ 30 VDC or 3 A @ 250 VAC
resistive load; 1/14 HP @ 125/250 VAC (50 watts) for induc-
tive loads

ELECTRICAL
NOISE
SUPPRESSION

A suppressor (snubber) should be connected to each relay
contact switching inductive loads to prevent disruption to the
microprocessor’s operation.
Recommended suppressor value: 0.01 µF/470

Ω

, 250 VAC

(PDX6901).

DEADBAND

0-100% of full scale, user selectable

HIGH OR LOW
ALARM

User may program any alarm for high or low trip point.

RELAY
OPERATION

Automatic (non-latching)
Latching
Pump alternation control

RELAY RESET

User selectable via front panel buttons or PC

Automatic reset only (non-latching)
Aut manual reset at any time (non-latching)
Manual reset only, at any time (latching)
Manual reset only after alarm condition has cleared (latching)
Automatic reset: Relays will automatically reset when the in-
put passes the reset point.
Manual reset: Front panel ACK button. Pressing ACK re-
sets all manually resettable relays.

TIME DELAY

0 to 199 seconds, on and off delays
Programmable and independent for each relay

FAIL-SAFE
OPERATION

Programmable
Independent for each relay

AUTO
INITIALIZATION

When power is applied to the meter, relays will reflect the
state of the input to the meter.

Fail-safe operation:

relay coil is energized in non-alarm condition. In

case of power failure, relay will go to alarm state.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

«
...
8
9
10
11
12
...
»

Summary of Contents for PD765-6X0-00








































































Reviews:

No comments

Related manuals for PD765-6X0-00

Brand: Hammond Pages: 754

Brand: Jennov Pages: 50

Brand: Oceanic Pages: 17

SMatrix DMX2400

Brand: dallmeier Pages: 12

Brand: Sensia Pages: 16

Signet FlowtraMag 2580 Series

Brand: GF Pages: 20

Brand: Ocea Soft Pages: 19

Brand: Kobold Pages: 55

Brand: YATO Pages: 36

Brand: Clavitech Pages: 56

Brand: Kawai Pages: 110

Brand: Wacom Pages: 23

Brand: F&F Pages: 4

Brand: RedBack Lasers Pages: 2

AERASGARD FSFTM-CO2-Modbus Series

Brand: S+S Regeltechnik Pages: 32

Brand: Ozito Pages: 8

Brand: Hanna Instruments Pages: 48

Brand: Teracom Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands