M1000E
ENGLISH
ISM1000EEU_02_14
8
3. Select function F3 by pressing keys INC (blue) and DEC (red) and confirm by pressing the VAL (green) key.
4. The letter P will appear on the left side of the display. Digit a sequence of six keys within 10 seconds. Each time a key is pressed, the letter P will
flash.
5. Upon the full sequence of six keys having been completed, the function selection menu will reappear on the display.
Failure to complete sequence within 10 seconds will abort password entry. This also avoids entry of incorrect passwords in case of any doubts as to
the sequence to be entered or erroneous pressing of any key.
The password is stored in EEPROM and is requested whenever INC (blue)+DEC (red) are pressed to access programming mode starting from the
stand-by status (displays being off). In this case:
1. The letter P appears on the left side of the display. Digit the sequence of six keys corresponding to the password. Each time a key is pressed, the
letter P will flash.
2. Upon the 6-key sequence being completed, programming mode is accessed. If sequence is erroneous, the displays will go off.
Upon programming mode being accessed, any resident password may be deleted or replaced with a new one.
Note: To remove a password which has been forgotten, contact system supplier.
Deleting a resident password
1.
Press INC (blue)+DEC (red) to access programming mode: the password will be requested.
2.
Digit in the password.
3.
Press the FUN (yellow) key to access the function selection menu.
4.
Select the password entry function F3 by pressing keys INC (blue) and DEC (red) and confirm by pressing key VAL (green).
5.
Allow time-out (10 seconds) to elapse; password is deleted and will not be requested upon any subsequent accessing of programming mode.
Entering a set of codes
Entry of a set of codes avoids having to perform learning of all the transmitters or of all the badges in case of packages of 10, 50 or 100 pieces with
consecutive codes.
1.
Access programming mode by pressing keys INC (blue)+DEC (red).
2.
Press the FUN (yellow) key to access the function selection menu.
3.
Select function F4 by pressing keys INC (blue) and DEC (red).
4.
Confirm by pressing the VAL (green) key. Request of the first location to be programmed will now appear, default value being 0001. Only the
first decimal point to the left will appear indicating that the initial location is being selected.
5.
Select location by pressing keys INC (blue) and DEC (red), and confirm by pressing the VAL (green) key.
6.
Request of final location to be programmed will now appear. The value shown is the one which has been previously selected as the initial
location so that only a value greater than this can be selected by pressing keys INC (blue) and DEC
(red). The last decimal point to the right will now appear indicating that the final location is being
selected.
7.
After selection of the final location, confirm by pressing the VAL (green) key. The M1000E will now
set itself up to accept transmission of a code. Once code has been received (via radio or any of the
connected readers), it is entered in the initial location. All subsequent locations up to the final one
may be entered with codes obtained by increasing the initial code by one unit.
Example: initial location = 120, final location = 127, received code = 112233
Upon all locations having been entered with the code, system will return to the function selection menu.
Deleting a set of codes
1.
Access programming mode by pressing keys INC (blue)+DEC (red).
2.
Press the FUN (yellow) key to access the function selection menu.
3.
Select function F5 by pressing keys INC (blue) and DEC (red).
4.
Confirm by pressing the VAL (green) key. Request of the first location to be deleted
(that is, the default value 0001) will now appear. Only the first decimal point to the left will appear indicating that the initial location is being
selected.
5.
Select location by pressing keys INC (blue) and DEC (red), and confirm by pressing the VAL (green) key.
6.
Request of final location to be deleted will now appear. The value shown is the one which has been previously selected as the initial location so
that only a value greater than this can be selected by pressing keys INC (blue) and DEC (red). The last decimal point to the right will now
appear indicating that the final location is being selected.
7.
After having selected the final location, confirm by pressing the VAL (green) key; the letter -C- will now appear on the left-hand side of the
display.
8.
Press the VAL (green) key again to confirm. The M1000E will now automatically delete all the codes stored in the set of programmed locations.
Upon deletion being completed, system will return to the function selection menu.
Deleting all codes
Deletion of all codes avoids having to scroll all locations and having to delete one code at a time in case of memory having to be fully cleared.
1. Access programming mode by pressing keys INC (blue)+DEC (red).
2. Press the FUN (yellow) key to access the function selection menu.
3. Select function F6 by pressing keys INC (blue) and DEC (red).
4. Confirm by pressing the VAL (green) key. The letter C will appear on the left side of the display.
5. Confirm again by pressing the VAL (green) key. The M1000E will fully delete the code area only. All other stored parameters (relay times,
channels, etc.) will remain unaltered.
Upon deletion being completed, system will return to the function selection menu.
Serial transferring of data
1.
Access programming mode by pressing keys INC (blue)+DEC (red).
2.
Press the FUN (yellow) key to access the function selection menu.
3.
Select function F7 by pressing keys INC (blue) and DEC (red).
4.
Confirm by pressing the VAL (green) key. Request of the first location to be transferred (that is, the default value 0001) will now appear. Only
the first decimal point to the left will appear indicating that the initial location is being selected.
Location
Code
120
⇒
112233
121
⇒
112234
122
⇒
112235
123
⇒
112236
124
⇒
112237
125
⇒
112238
126
⇒
112239
127
⇒
112240
