background image

 

31 

 PowerMaster 

Limited 5 Year Warranty 

 

PowerMaster warrants all gate operators to be free of defects in 
materials and workmanship for a period of Five (5) years from date 
of purchase.  If any part is found to be defective during this period, 
new parts will be furnished free of charge.  Failure of this product 
due to misuse, improper installation, alterations, vandalism, or lack 
of maintenance is not covered under this warranty, and voids any 
other implied warranties herein.  

 

PowerMaster is not responsible for any labor charges incurred in 
connection with the installation of warranted parts. 

 

In order to activate this warranty, the registration form on 
opposite page MUST be completed and returned within 
THIRTY CALENDER DAYS FROM DATE OF PURCHASE 
VIA CERTIFIED MAIL.

 

If registration is not activated, a one 

year warranty will apply. 

 
 
 
 

 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 

 

32 

 

Model MBG

   

 Date Installed____________ 

 Serial # ________________ 

Location 

Installed: 

    

Address: ___________________ 

Address: ___________________ 

Address: ___________________ 

Installer’s Information 

Company Name _____________________    Company Telephone # ______________ 

Company Address ___________________    Company Contact _________________ 

Company Address ___________________ 

Company Address ___________________ 

Summary of Contents for MBG

















Reviews: