S
TEP
3:
O
PERATING
O
NE
D
OOR
O
PENER
To open or close
the
Garage Door.
• Enter your PIN.
• Press .
S
TEP
2:
Find the Learn Code Button and Learn Code
Indicator LED on your door opener.
–
– If your Door Opener
does not
have an Antenna,
you have an External Receiver.
The External Receiver cover
must be removed to access
the Learn Code Button
and Indicator LED.
• Press the Learn Code Button.
– Learn Code Indicator LED (on Opener) will blink.
• Enter your PIN and press on
Keypad.
– Learn Code Indicator LED stays on.
• Press again.
– Learn Code Indicator LED turns off.
B
ASIC
P
ROGRAMMING FOR
O
NE
D
O
INTELLICODE®
OR
O
PENER
D
O
INTELLICODE®
OR
O
PENER
P
ROGRAMMING FOR
2
OR
3
FOR CONVENIENCE
Program Keypad
BEFORE
mounting.
SECTION
1
SECTION
2
FOR CONVENIENCE
Program Keypad
BEFORE
mounting.
Proceed to Section 3 - Mounting Instructions.
NOTE
•
If the Door does not move,check the red LED on
Keypad. If the LED is blinking rapidly,the PIN was
entered incorrectly. After the LED stops blinking,re-enter
your PIN and try again.
•
Any Keypad Button will control the Door for 30 seconds
after the Door starts moving.
•
Rapid blinking of the red LED indicates an error. After a
few seconds the LED will turn off. Start over.
Wait until Keypad Backlight turns off (approximately 30 seconds).
• Press again.
– Opener will run.
S
TEP
1:
C
REATING
Y
OUR
W
IRELESS
K
EYPAD
PIN
(P
ERSONAL
I
DENTIFICATION
N
UMBER
)
• Press in order .
• Press
.
• Enter your PIN (3 to 8 characters).
•
• Close keypad cover and wait 30 seconds.
Press
.
3
5
7
• Press in order .
• Press
.
• Enter your PIN (3 to 8 characters).
•
• Close keypad cover and wait 30 seconds.
Press
.
3
5
7
S
TEP
1:
C
REATING
Y
OUR
W
IRELESS
K
EYPAD
PIN
(P
ERSONAL
I
DENTIFICATION
N
UMBER
)
T
EACHING
PIN
TO
S
INGLE
O
PENER
©2010 GMI Holdings, Inc. D.B.A.The Genie Compan y
Red Indicator
LED
Learn
Code
Button
Located
on Opener
Housing
PROGRAM
PROGRAM
PROGRAM
PROGRAM
Decide which Door will be Door #1,#2 and #3.
• Enter your PIN and press on Keypad.
• Press the
• Press and hold the for 2 seconds.
number you have picked for this
Door Opener ( or or ).
• Press 3 times.
– Opener will run.
Repeat procedure below dotted line for each opener.
(Each Door Opener must be programmed to receive the
signal from the Wireless Keypad).
S
TEP
3:
O
PERATING
M
ULTIPLE
D
OOR
O
PENERS
To open or close
a Door after programming is complete.
• Enter your PIN.
• Press .
• Press Door Opener number ( or or ).
S
TEP
2:
All Door Openers will use the same PIN.
On your keypad:
• Enter your PIN and press
.
• Press
again.
• Press the number of Doors (total) you wish
to control ( or ).
•
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Press
.
Wait until Keypad Backlight turns off (approximately 30 seconds).
2
3
1
2
3
1
2
3
P
ROGRAMMING
M
ULTIPLE
D
OOR
O
PENERS
PROGRAM
PROGRAM
PROGRAM
PROGRAM
• Press the Learn Code Button. (See Step 2 in Section 1.)
If your Door Opener has a black
antenna wire
and
the serial
number does not start with
10 or higher, the Learn Code
Button and Indicator LED are
located near the antenna. (The
light lens may need to be
opened. If you use an external
receiver, it may need to be opened
to access the Learn Code Button
and Indicator LED.
For answers to questions, call 1-800-35- GENIE , or visit
www.geniecompany.com
A
The Genie Company, 22790 Lake Park Blvd., Alliance, Ohio 44601
dditional Genie® products can be ordered through your local
Genie® Professional Dealer. To locate a dealer near you,
call 1-800-OK-GENIE.
To Operate Intellicode® 1 Openers:
This Wireless Keypad comes from the factory as an Intellicode® 2 unit.
In order to initially program an opener or openers which are
Intellicode®1, you must switch the Keypad to Intellicode®1 mode.
• After entering your PIN, Press .
•
•
•
Press and hold for two seconds and the
GREEN LED above the number keys will turn RED.
PROGRAM
Once all your doors have been programmed, there is no need to
switch back and forth between Intellicode® modes. The Keypad will
automatically remember the mode of each opener.
Close the Keypad cover.
Follow the instructions on this page for programming
your Intellicode® 1 opener(s).
WIRELESS KEYPAD INTELLICODE® 1 MODE
