background image

 9 

 

3. 

DO NOT 

allow children to play near your gate, or 

to operate the gate.

 

 

 

 

4. 

DO NOT

 

operate your gate system unless you can 

see it when the gate moves.

 

 

 

5. Be sure a pushbutton or key switch has been 

installed for manual electric operation in the event 
your radio or card does not work. Any mounted 
control station should be located a minimum of 10 
feet from the gate so the gate cannot be touched. 
Any pushbutton located in a building should be 
installed within sight of the gate.

 

 

 

6. 

DO NOT

 

operate any controls without watching the 

movement of the gate

 

 

7.  Be sure the gate arm DOES NOT come within 2 

feet of any rigid object, therefore causing an 
entrapment situation.

 

 

10 

FEET

 

 

8. If your gate closes automatically, loop detectors 

should be installed to detect the presence of a vehicle.

 

 

 

9.  If a contact or non-contact safety system has been 

installed check for proper operation at least once per 
month. 

If these functions are observed to operate 

improperly, discontinue use and have it serviced 
immediately! 

 

 

10. To ensure safe operation of this equipment, you 

must read this safety manual and keep it for reference.

 

 

 

MANUAL OPERATION 

 

. Please refer to page 18 for Manual Operation 

Instructions.

 

Summary of Contents for MBG

















Reviews: