background image

POWER ELECTRONICS 

PROFIPOWER 

 

 

TRIAL RUN 

41

4.3.6.

 

Profipower SD700 Type 4 Module 

This is also a pre-defined module, although broader than the 

previous one. A high number of Modbus registers for reading and 

writing has been defined. User only must write the value of the 

registers. 

Pre-defined registers for these modules are shown in the attached 

table.

 

The Profipower gateway receives 54 bytes of output data of the 

ProfiBus-DP Master. 

 

Output Data (Word) 

Variables 

0 LOCAL_SPEED_REF 
1 HOST_START_CONTROL 
2 HOST_STOP_CONTROL 
3 HOST_RESET_CONTROL 
4 HOST_TRIP_CONTROL 
5 LIMIT1_MIN_SPEED 
6 LIMIT2_MIN_SPEED 
7 LIMIT1_MAX_SPEED 
8 LIMIT2_MAX_SPEED 
9 CURRENT_LIMIT 
10 TORQUE_LIMIT 
11 INVERTED_SPEED_ENABLED 
12 NAMEPLATE_MOTOR_CURRENT 
13 NAMEPLATE_MOTOR_POWER 
14 ACCELERATION_RATE 
15 ALT_ACCELERATION_RATE 
16 DECELERATION_RATE 
17 ALT_DECELERATION_RATE 
18 ACC_BRAKE_SPEED 
19 DEC_BRAKE_SPEED 
20 CURRENT_LIMIT_TIMEOUT 
21 STOP_TIMEOUT 
22 TORQUE_LIMIT_TIMEOUT 
23 SUPPLY_UNDER_VOLTAGE 
24 SUPPLY_OVE_VOLTAGE 
25 CURRENT_LIMIT 
26 TORQUE_LIMIT 

Summary of Contents for Profipower




















































Reviews: