POSBank A10plus Command Reference Manual Download Page 118

Page: 118 / 122

- 118 -

Rev. 1.50

A10plus MiniPrinter

CONFIDENTIAL

GS ( F pL pH a m nL nH

[Name]

Set black mark adjustment value

[Format]

ASCII

(

Hex.

Decimal

[Range]

(

x256) = 4,

= 4,

= 0

≤

= 0,1,48,49

≤

× 256

≤

65535, 0

≤

255, 0

≤

255

[Default]

All adjustment values = 0

[Description]

Sets the adjustment value of the black mark detection position.

a specifies the type of adjustment value.

Function

Sets the adjustment value of the black mark detection position.

Sets the adjustment value of the paper cutting position after black

mark detection.

m specifies the direction of adjustment.

Function

0, 48 Forward Direction (Paper Feed Direction)

1, 49 Reverse Direction

nL, nH specify the amount of adjustment.

[Notes]

•

When processing this command while defining a macro, the macro definition is

Immediately terminated and the command commences with processing.

Summary of Contents for A10plus



























































































































Search results

Summary of Contents for A10plus

Reviews:

POSBank A10plus, Command Reference Manual, Page: 118 / 122

Search results

Summary of Contents for A10plus

Reviews: