PortaCo G-18S10-54-W Operation Manual Download Page 27

Page: 27 / 28

HYDRAULIC POWER UNIT G-18S10-54-W

OPERATION MANUAL

Maintenance and repairs

8.1

General information for maintenance and repairs

Goals of the maintenance are:

-

to find and evaluate causes for malfunction

initiate measures to solve malfunction

fix malfunction and restore operational readiness

Repairs to the machine may only be carried out by the PortaCo Inc. or personnel who have been specially instructed. Additionally,
work on electrical system parts may only be made by electrical specialists.

8.2

Troubleshooting and repairs

Malfunction

Possible causes

Remedy

Device not working or too
slow

Hydraulic fluid level too low

Top off hydraulic fluid or replace

Connection not airtight or loose

Check connections and seals and tighten, or
replace seals

Air in device

Bleed system

Mechanical error

Check the entire device for damage

Operating lever stiff

Counter pressure too high

17 bar and 38 lpm should not be exceeded

Device soiled

Clean the device

Hydraulic fluid leak

Damaged seal

Remove device and replace seals

Table 7: Troubleshooting

Summary of Contents for G-18S10-54-W





























Search results

Summary of Contents for G-18S10-54-W

Reviews:

Related manuals for G-18S10-54-W

Brands by name

Popular brands

PortaCo G-18S10-54-W, Operation Manual

Search results

Summary of Contents for G-18S10-54-W

Reviews:

Related manuals for G-18S10-54-W

Brands by name

Popular brands