Playnation Redbrook with Monkey Bars 382 Manual Download Page 86

Page: 86 / 111

TELESCOPE MOUNTING BRACKETS

TELESCOPE

TELESCOPE BASE

PROVIDED

HARDWARE

STEP 46: TELESCOPE

1: PLACE ONE OF THE L-SHAPE TELESCOPE MOUNTING BRACKETS CENTERED ON THE PANEL

SUPPORT.
2: ATTACH THE L-SHAPED BRACKET WITH TWO SCREWS PROVIDED WITH THE TELESCOPE.
3: PLACE THE BASE OF THE TELESCOPE INTO THE CUT OUT AREA OF THE

-SHAPED BRACKET.

4: ATTACH ANOTHER

-SHAPED TELESCOPE MOUNTING BRACKET DIRECTLY ACROSS FROM THE

PREVIOUSLY INSTALLED BRACKET AND SECURE WITH THE PROVIDED HARDWARE.
NOTE: THE REMAINING TWO BRACKETS THAT ARE "C" SHAPED ARE FOR MOUNTING THE

TELESCOPE ON TOP OF A 4 X 4 PIECE OF WOOD. THEY MAY BE RECYCLED OR YOU MAY RETAIN

THEM IF YOU WISH.

Summary of Contents for Redbrook with Monkey Bars 382
















































































































Search results

Summary of Contents for Redbrook with Monkey Bars 382

Reviews:

Related manuals for Redbrook with Monkey Bars 382

Brands by name

Popular brands

Playnation Redbrook with Monkey Bars 382, Manual

Search results

Summary of Contents for Redbrook with Monkey Bars 382

Reviews:

Related manuals for Redbrook with Monkey Bars 382

Brands by name

Popular brands