Playnation Redbrook with Monkey Bars 382 Manual Download Page 78

Page: 78 / 111

STEP 38: ROOF BOARDS / ROOF FINISHERS

AND

CHIMNEY AND DORMERS

1: PLACE THE 1 X 5 X 52" ROOF BOARDS ON TOP OF THE ROOF SUPPORTS, FITTING THE TONGUE

INTO THE GROOVE OF THE ROOF STARTER. THE HOLES IN THE ROOF BOARDS SHOULD BE

CENTERED OVER THE ROOF SUPPORTS. THERE ARE SEVEN ROOF BOARDS ON EACH SIDE OF THE

ROOF. IF NECESSARY PLACE A SCRAP 2 X 4 BOARD AGAINST THE ROOF BOARD AND HAMMER

ON IT TO SEAT THE TONGUE INTO GROOVE FOR THE ROOF BOARDS. FASTEN EACH ROOF

BOARD TO THE ROOF SUPPORTS WITH FOUR 1-1/2" WOOD SCREWS.
2: PLACE THE 1 X 5 X 52" ROOF FINISHER AT THE END OF THE ROOF ASSEMBLY AND FASTEN TO

THE ROOF SUPPORTS WITH FOUR 1-1/2" WOOD SCREWS. EACH SIDE OF THE ROOF GETS ONE

ROOF FINISHER.

TIP

: USE THE INSTRUCTIONS PROVIDED IN THE APPENDIX TO BUILD THE CHIMNEY AND DORMERS.

AFTER PUTTING IN THREE ROOF BOARDS ON THE FRONT ROOF

STOP

AND THEN INSTALL THE

CHIMNEY. NOTICE THE MOUNTING BLOCK FOR THE CHIMNEY WILL GET INSTALLED ON THE FIRST

ROOF BOARD. ONCE ALL THE ROOF BOARDS / FINISHERS ARE INSTALLED MOUNT THE DORMERS

AS SHOWN BELOW CENTERED ON THE ROOF.

WOOD SCREW

(FIRST ONE)

#8 X 1-1/2"

WOOD SCREW

ROOF BOARD

1 X 5 X 52"

#8 X 1-1/2"

CHIMNEY

Summary of Contents for Redbrook with Monkey Bars 382
















































































































Search results

Summary of Contents for Redbrook with Monkey Bars 382

Reviews:

Related manuals for Redbrook with Monkey Bars 382

Brands by name

Popular brands

Playnation Redbrook with Monkey Bars 382, Manual

Search results

Summary of Contents for Redbrook with Monkey Bars 382

Reviews:

Related manuals for Redbrook with Monkey Bars 382

Brands by name

Popular brands