Playnation Redbrook with Monkey Bars 382 Manual Download Page 46

Page: 46 / 111

DECK SUPPORT

HEX BOLT

2 X 4 X 47-3/8"

5/16" WASHER

T-NUT

(OFFSET HOLES DOWN)

5/16" WASHER

(HOLES OFFSET DOWN)

2 X 4 X 47-3/8"

(HOLES OFFSET DOWN)

5/16" X 4-1/2" HEX BOLT

PANEL SUPPORT

DECK SUPPORT

2 X 4 X 47-3/8"

5/16" X 4-1/2"

T-NUT

2 X 6 X 47-3/8"

FRONT ARCH BOARD

STEP 6: PANEL SUPPORTS AND DECK SUPPORTS

1: USE A HAMMER TO SEAT THE T-NUTS AFTER INSERTING THEM INTO THE HOLES SHOWN IN THE

DIAGRAM BELOW.
2: THE 2 X 4 X 47-3/8" PANEL SUPPORT (OFFSET HOLES DOWN) ATTACHES TO THE REAR OF THE

LEFT REAR AND RIGHT REAR CORNER POSTS WITH TWO 5/16" X 4-1/2" HEX BOLTS AND TWO 5/16"

WASHERS.
3: THE 2 X 6 X 47-3/8" FRONT ARCH BOARD ATTACHES TO THE FRONT OF THE LEFT AND RIGHT

CORNER POSTS WITH TWO 5/16" X 4-1/2" HEX BOLTS AND TWO 5/16" WASHERS.
4: ATTACH THE 2 X 4 X 47-3/8" DECK SUPPORTS (OFFSET HOLES DOWN) TO THE INSIDE OF THE

LEFT AND RIGHT CORNER POSTS WITH TWO 5/16" X 4-1/2" HEX BOLTS AND TWO 5/16" WASHERS.

Summary of Contents for Redbrook with Monkey Bars 382
















































































































Search results

Summary of Contents for Redbrook with Monkey Bars 382

Reviews:

Related manuals for Redbrook with Monkey Bars 382

Brands by name

Popular brands

Playnation Redbrook with Monkey Bars 382, Manual

Search results

Summary of Contents for Redbrook with Monkey Bars 382

Reviews:

Related manuals for Redbrook with Monkey Bars 382

Brands by name

Popular brands