background image

Copyright Planika Sp. z o.o.  

www.planikafires.com 

 

IG0098#01 

19.02.2018 

 

17 

Gas cylinder connection 

Twist-on connection 

Quick-release 

1.

 

Check if the bottle valve is TURNED OFF turning 
it clockwise 

2.

 

Remove the protection tip and store it for later 
use. 

1.

 

Remove the protection tip. Do not use any tools, 
leave the tip hanging freely.

 

3.

 

Before making the connection check if the black 
seal is not damaged. 

 

2.

 

Make  sure  all  the  taps  on  the  gas  device  are 
closed and if the switch in in the OFF position. 

 

4.

 

Fit  the  connecting  nut  to  the  cylinder  with  the 
use of a correct wrench or the connecting knob. 
(left  thread)  Do  not  allow  the  gas  cylinder 
connectors to be fastened too tightly. 

 

3.

 

Place  the  quick-release  regulator  on  the  valve 
and press it down hard. If the switch is correctly 
turned off you will hear a characteristic click. 

 

5.

 

When the gas flow is required turn the valve of 
the bottle counter-clockwise. 

 

4.

 

To let the gas flow in turn the switch into the ON 
position (or into the flame image). 

 

 

Place the gas cylinder in a correct distance from the fireplace (min 1,5 metres away).  

 

WARNING!!!

 

Check the gas connection for leakage. If anything suggests a leak is present (for instance a 

characteristic gas smell) close the gas cylinder valve and under no circumstances turn the device on before 

removing the leak.

 

 

After removing the leak one may open the gas cylinder valve again. 

 

Summary of Contents for GaLiO Insert #2






















Reviews: