background image

Copyright Planika Sp. z o.o.  

www.planikafires.com 

 

IG0098#01 

19.02.2018 

 

2.1

 

Safety instruction regarding the use of the gas cylinder 

 

Use only the type of gas and pressure specified by the manufacturer. 

 

The gas cylinders should always be placed in a vertical position – during use and transport. 

 

Always store the gas cylinder in an easily accessible place to allow its immediate turn-off. 

 

During the installation process do not allow an open flame or any ignited object to reach the gas cylinder.  

 

The gas cylinder should be in a distance not shorter than 1,5 metres away from the GaLiO Insert fireplace. 

 

Leaks should be found with the use of a cleaning liquid and water. If bubbles form on the surface that means 

that a there’s an existing leak. 

 

Always use a pressure regulator between the gas cylinder and the device. Replace the pressure regulator every 

5 years. The allowed pressures are: 30mbar, 37mbar (recommended), 50 mbar. Use only regulators complying 

with the European EN16129 Norm.  

 

Use only approved and certified gas connection linkage. Replace the linkage every 2 years. 

 

The elastic linkage connecting gas to the fireplace is to be led away from sharp edges and hot surfaces. Refrain 

from bends and twists of the elastic connection on its full length. 

 

Remember that the LPG bottle should be stored in a well-ventilated place. LPG gas is heavier than air and its 

accumulation near the surface may generate an explosive mixture. 

 

The  housing  in  which  the  LPG  bottle  is  (optionally)  placed  needs  to  have  an  appropriate  ventilation.  The 

housing needs to have an upper ventilation slot above the top of the bottle (of an area min 1/100 of the area 

of the base of the housing) and a lower ventilation slot (of an area min 1/50 of the area of the base of the 

housing). 

 

The gas cylinder needs to be shut if the fireplace is not being used. 

 

Filling the gas cylinders is to be commissioned to certified gas filling stations. 

 

Replacement of empty bottles for full ones is to be conducted only in authorized locations. 

 

3.

 

INSTALLATION 

3.1.

 

Box contents 

 

 

1x complete gas fireplace 

 

1x Wall Switch 

 

4x AA Batteries  

 

4x bag of decorative stones 

 

1x 4 metre rubber gas linkage – installed (only LPG version) 

 

1x pressure regulator (37mbar) – installed (only LPG version) 

 

1x Euro Set (only LPG version) 

 

1x installation manual 

 

1x user’s manual 

 

 

 

 

Summary of Contents for GaLiO Insert #2






















Reviews: