Planika GaLiO Insert #2 Installation Manual Download Page 18

Page: 18 / 21

www.planikafires.com

IG0098#01

19.02.2018

Disconnection of the gas cylinder

Twist-on connection

Quick-release

Turn off the GaLiO Insert – put it into the OFF position. The main and pilot burner need to be
turned off.

Turn the bottle valve into the OFF position
(clockwise).

Turn the switch into the OFF position.

NEVER DO NOT unmount the regulator (or
connecting nut) when the bottle valve is
open.

TAKE OFF the regulator (or the connecting
nut) with the use of a wrench or a
connecting knob.

Take  off  the  quick-release  regulator  by
pressing  the  switch  horizontally  and
simultaneously  pulling  the  whole  regulator
upwards.

REPLACE the linkage closer or cap on the
empty or partially full bottle if it’s not being
used.

REPLACE the tightening cap on an empty or
partially full bottle if it’s not being used.

5.3

Adapters for the gas cylinder connection (LPG version)

When the thread of the installed pressure regulator does not fit into the thread on the valve of the gas cylinder,

it is necessary to use an appropriate adapter that is delivered with the device.

Summary of Contents for GaLiO Insert #2






















Search results

Summary of Contents for GaLiO Insert #2

Reviews:

Related manuals for GaLiO Insert #2

Brands by name

Popular brands

Planika GaLiO Insert #2, Installation Manual

Search results

Summary of Contents for GaLiO Insert #2

Reviews:

Related manuals for GaLiO Insert #2

Brands by name

Popular brands