Planet WNAP-1260 User Manual Download Page 55

Page: 55 / 154

User’s Manual of WNAP-1260

-47-

6.6.4. Upgrade

Choose

Management Function

Upgrade

and the

Upgrade

page is displayed.

Figure 6-16

Upgrade the software of the router in the following steps:

Step 1

Click

Browse…

to navigate to the latest software.

Step 2

Select the correct upgrade file. If you select

Clear Config

, the router restores to the

default settings after upgrade. If you do not select it, the current settings remain.

Step 3

Click

Upload

to start upgrade.

After the upgrade is completed, the router automatically reboots.

After the software upgrade, WNAP-1260 returns to the factory default settings. In case of
losing the previous configuration information, please save settings before updating the
software. Do not power off the device during upgrade.

Summary of Contents for WNAP-1260



























































































































































Search results

Summary of Contents for WNAP-1260

Reviews:

Related manuals for WNAP-1260

Brands by name

Popular brands

Planet WNAP-1260, User Manual

Search results

Summary of Contents for WNAP-1260

Reviews:

Related manuals for WNAP-1260

Brands by name

Popular brands