Planet WNAP-1260 User Manual Download Page 131

Page: 131 / 154

User’s Manual of WNAP-1260

-123-

Figure 9-20

In this page, you can view information about the current running status of WNAP-1260, including
system information, LAN port status, and wireless client status.

10.3.2. Clients List

Choose

Running Status

Clients List

and the

Clients List

page is displayed.

Figure 9-21

This page displays information of wireless devices connected to WNAP-1260, including the IP adress
and MAC address of each device.

10.4. Setup Wizard

For settings, refer to section 5.5. “

Client Mode Configuration

”.

10.5. Network Settings

Click

Network Settings

and the extended navigation menu is shown as follows:

Click a submenu to perform specific parameter configurations.

Summary of Contents for WNAP-1260



























































































































































Search results

Summary of Contents for WNAP-1260

Reviews:

Related manuals for WNAP-1260

Brands by name

Popular brands

Planet WNAP-1260, User Manual

Search results

Summary of Contents for WNAP-1260

Reviews:

Related manuals for WNAP-1260

Brands by name

Popular brands