Planet WNAP-1260 User Manual Download Page 46 | Manualshive

Page: 46 / 154

background image

User’s Manual of WNAP-1260

-38-

6.4. Network Settings

Click

Network Settings

and the extended navigation menu is shown as follows:

Click a submenu to perform specific parameter configurations.

6.4.1. LAN Interface Settings

Choose

Network Settings

>

LAN Interface Settings

and the

LAN Interface Settings

page is

displayed.

Figure 6-4

You can modify the IP address and IP subnet mask of the LAN port as required.

If you change the default IP address, you must use the new IP address to log in to the Web
configuration page of the router and the default gateway of all hosts in the LAN must be
set to the new IP address for internet access. The subnet mask of all hosts in the LAN
must be the same as the subnet mask specified in the LAN Interface Settings page.

6.4.2. DHCP Server

Choose

Network Settings

>

DHCP Server

and the

DHCP Server

page is displayed.

DHCP refers to Dynamic Host Configuration Protocol. If

Use Device as DHCP Service

is selected,

WNAP-1260 automatically assigns IP addresses to comupters in the LAN. Users do not need to
configure TCP/IP protocol paramters such as the IP address, the subnet mask, the gateway, and the
DNS server information for computers connected to the router’s LAN.

«
...
44
45
46
47
48
...
»

Summary of Contents for WNAP-1260



























































































































































Reviews:

No comments

Related manuals for WNAP-1260

Brand: EDM Product Pages: 25

Brand: Rowley Pages: 6

The Hot One RCP402S

Brand: Cadet Pages: 8

Brand: Oceanic Pages: 23

Brand: DELLA Pages: 14

Brand: Lifestyle Pages: 16

The Com-Pak CB132T

Brand: Cadet Pages: 8

Brand: Cabletron Systems Pages: 80

Brand: Trane Pages: 16

MIL 03 08 Series

Brand: LVI Pages: 20

Brand: Rinnai Pages: 32

Brand: dellonda Pages: 5

Brand: Andrew Pages: 66

Brand: Zehnder Rittling Pages: 58

Brand: Trotec Pages: 68

Versa Hydro PHE130-119

Brand: HTP Pages: 84

Brand: Glen Pages: 4

Brand: Tansun Quartzheat Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands