Pioneer AVIC-Z610BT Operation Manual Download

Page: 77 / 90

glis

problem, contact your dealer or an

authorised Pioneer Station for

assistance.

Positioning is not possible due to

hardware error. Please consult your

dealer or local authorised service centre.

→

The location display is not possible due

to hardware failure.

– Contact your dealer or an authorised

Pioneer Station for assistance.

No GPS antenna. Check connection.

→

GPS reception is lost.

– Check the aerial connection. If the

message fails to disappear even after

the engine is switched off/on, contact

your dealer or an authorised Pioneer

Station for assistance.

GPS antenna problem detected. Contact

dealer or service center.

→

GPS aerial lead is short-circuited.

– Contact your dealer or an authorised

Pioneer Station for assistance.

Calibration will start, but may be

inaccurate without speed pulse.

→

The speed pulse sensor is not

connected correctly.

– Contact your dealer or an authorised

Pioneer Station for assistance.

Sensor error. Please contact your dealer

or Pioneer Service Center.

→

An error has occurred with the sensor.

– Contact your dealer or an authorised

Pioneer Station for assistance.

Detected unusual speed pulses.

→

The speed pulse cannot be detected

correctly.

– Contact your dealer or an authorised

Pioneer Station for assistance.

Detected changes in the installation

angle or position. The in-dash receiver is

updating the sensor learning data.

→

Changes in the installation angle or

position are detected.

– Wait until the sensor learning finishes.

Speed pulse wire is not connected. The

system will operate in simple hybrid

mode.

→

Speed pulse wire is not connected.

– The speed pulse cannot be detected if

the speed pulse wire is not connected

correctly.

Check Antenna

→

The aerial connection is incorrect or an

unusual voltage has been detected.

– Turn the ignition switch OFF and

connect the aerial correctly. After

connecting, turn back ON again.

Error-02-XX/FF-FF

→

The disc is dirty.

– Clean the disc.

→

The disc is scratched.

– Replace the disc.

→

The disc is loaded upside down.

– Check that the disc is loaded correctly.

→

There is an electrical or mechanical

error.

– Press the RESET button.

Different Region Disc

→

The disc does not have the same region

number as this product.

– Replace the DVD with one bearing the

correct region number.

DAB tuner

Disc

Z910DAB Z810DAB Z710DAB Z7110DAB

Unplayable Disc

→

This type of disc cannot be played on

this product.

– Replace the disc with one that can be

played on this product.

Unplayable File

→

This type of file cannot be played on this

product.

– Select a file that can be played.

Skipped

→

The inserted disc contains DRM

protected files.

– The protected files are skipped.

Protect

→

All the files on the inserted disc are

embedded with DRM.

– Replace the disc.

This DivX rental has expired.

→

The inserted disc contains expired DivX

VOD content.

– Select a file that can be played.

Video resolution not supported

→

Files that cannot be played on this

product are included in the file.

– Select a file that can be played.

Unable to write to flash memory

→

The playback history for VOD contents

cannot be saved for some reason.

– Retry.

– If the message appears frequently,

consult your dealer.

Your device is not authorized to play this

DivX protected video.

→

This product’s DivX registration code

has not been authorised by the DivX

VOD contents provider.

– Register this product to the DivX VOD

contents provider.

Video frame rate not supported

→

DivX file’s frame rate is more than 30 fps.

– Select a file that can be played.

Audio Format not supported

→

This type of file is not supported on this

product.

– Select a file that can be played.

SD function is only available for AVIC-

Z910DAB/AVIC-Z810DAB.

Error-02-9X/-DX

→

Communication failed.

– Turn the ignition switch OFF and back

ON.

– Disconnect the USB storage device.

– Change to a different source. Then,

return to the USB storage device.

Unplayable File

→

There is no playable file in the external

storage device (USB, SD).

– Check that the files in the external

storage device (USB, SD) are

compatible with this product.

→

Security for the connected external

storage device (USB, SD) is enabled.

– Follow the external storage device

(USB, SD) instructions to disable

security.

Skipped

→

The connected external storage device

(USB, SD) contains DRM protected files.

– The protected files are skipped.

Protect

→

All the files on the connected external

storage device (USB, SD) are embedded

with DRM.

– Replace the external storage device

(USB, SD).

External storage device (USB,
SD)

Summary of Contents for AVIC-Z610BT


























































































Search results

Summary of Contents for AVIC-Z610BT

Reviews:

Related manuals for AVIC-Z610BT

Brands by name

Popular brands

Pioneer AVIC-Z610BT, Operation Manual

Search results

Summary of Contents for AVIC-Z610BT

Reviews:

Related manuals for AVIC-Z610BT

Brands by name

Popular brands