PIONEER DJ DDJ-1000STR Operating Instructions Manual Download Page 8 | Manualshive

Page: 8 / 132

background image

Before you start

8

En

About the Serato DJ Pro software

Serato DJ Pro is a DJ software application made by Serato Limited.
DJ performances are enabled by connecting the unit to your PC/Mac
with the software installed.

Minimum computer requirements

•

32-bit operating systems not supported.

•

For information on the latest system requirements, compatibility, and
supported operating systems of Serato DJ Pro, visit the website
below.
https://serato.com/dj/pro/downloads

Supported operating systems

CPU and memory required

Mac: macOS Mojave 10.14 /
macOS High Sierra 10.13 /
macOS Sierra 10.12
(latest update)

Intel

®

processor Core™ i3, i5, i7

and i9
1.07 GHz or better

4 GB or more of RAM

Windows: Windows

®

10 /

Windows

®

8.1 / Windows

®

7

(latest service pack)

Intel

®

processor Core™ i3, i5, i7

and i9
1.07 GHz or better

4 GB or more of RAM

Others

USB port

Your PC/Mac must have a USB 2.0 port to
connect with the unit.

Display resolution

Resolution of 1280 × 720 or greater

Internet connection

You’ll need an internet connection to
register your user account at Serato.com
and to download the software.

«
...
6
7
8
9
10
...
»

Summary of Contents for DDJ-1000STR





































































































































Reviews:

No comments

Related manuals for DDJ-1000STR

Brand: OMCA Pages: 72

Brand: Barko Hydraulics Pages: 92

Brand: GBC Pages: 8

Brand: KAPSCH Pages: 57

Brand: Landoll Pages: 34

Brand: Makita Pages: 84

Brand: K&K Pages: 8

FlexDraper FD2 Series

Brand: MacDon Pages: 2

OXYGEN PRO MINI

Brand: M-Audio Pages: 56

Brand: YMC Pages: 49

Brand: Octane Fitness Pages: 8

Brand: Octane Fitness Pages: 10

Brand: OCENCO Pages: 48

Brand: Ocean Optics Pages: 6

Brand: V-TAC Pages: 13

EVENTWASH VL800

Brand: Vari Lite Pages: 23

Brand: Vapotherm Pages: 15

LSP400 LED Series

Brand: WE-EF Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands