PIONEER DJ DDJ-1000STR Operating Instructions Manual Download

Page: 12 / 132

Before you start

2 Double-click

[DDJ-1000SRT_X.XXX.exe]

3 Follow the on-screen instructions to install.

[Windows Security]

appears on the screen during installation, click

[Install

this driver software anyway]

and continue with the installation.

When the installation program is finished, a completion message appears.
After installing the driver software, install the Serato DJ Pro software.

4 Unzip the downloaded Serato DJ Pro software file.

5 Double-click the unzipped software file to launch the installer.

6 Read the terms of the license agreement carefully, and if you agree,

select

[I agree to the license terms and conditions]

, then click

[Install]

•

If you don’t agree to the contents of the license agreement, click

[Close]

cancel the installation.

A message indicating successful installation appears when installation is
complete.

Summary of Contents for DDJ-1000STR





































































































































Search results

Summary of Contents for DDJ-1000STR

Reviews:

Related manuals for DDJ-1000STR

Brands by name

Popular brands

PIONEER DJ DDJ-1000STR, Operating Instructions Manual

Search results

Summary of Contents for DDJ-1000STR

Reviews:

Related manuals for DDJ-1000STR

Brands by name

Popular brands