PIONEER DJ DDJ-1000STR Operating Instructions Manual Download Page 86

Page: 86 / 132

Advanced use

PHASER

The Phaser effect changes according to the beat you set with the

[BEAT





]

buttons.

The phaser effect changes according to the set beat button.

• [BEAT





]

buttons

Sets the cycle for moving the Phaser effect with respect to 1 beat of
BPM between 1/16 and 64 beats.

• [LEVEL/DEPTH]

knob

The further clockwise the control is turned, the greater the effect is
stressed.
When turned all the way counterclockwise, only the original sound is
output.

PITCH

Changes the pitch of the original sound.

• [BEAT





]

buttons

Sets the pitch of the effect sound between -50 and 100%.

• [LEVEL/DEPTH]

knob

Sets the pitch of the effect sound.
When you turn the knob all the way counterclockwise, the setting
returns to the pitch of the original sound.

Phase shift

Cycle

Time

Summary of Contents for DDJ-1000STR





































































































































Search results

Summary of Contents for DDJ-1000STR

Reviews:

Related manuals for DDJ-1000STR

Brands by name

Popular brands

PIONEER DJ DDJ-1000STR, Operating Instructions Manual

Search results

Summary of Contents for DDJ-1000STR

Reviews:

Related manuals for DDJ-1000STR

Brands by name

Popular brands