Pilot-1 WACO YKS-6 User Manual Download Page 28

28 

 

WARNING – THIS IS NOT A TOY! 

Radio controlled model aircraft are capable of inflicting serious injury and/or property damage if not assembled, operated, and 

maintained in a competent and safe manner.  If you are not already experienced with radio controlled models, we strongly suggest 

that you find an experienced modeler to assist you. 

 

Warranty 

Hobby-Lobby guarantees this kit to be free from defects in both material and workmanship at the date of purchase.  This warranty 
does not cover any component parts damaged by use or modification.  In no event shall Hobby-Lobby’s liability exceed the original 

cost of the purchased kit. 

 

2008 Official Academy of Model Aeronautics National Model Aircraft Safety Code 

 

GENERAL 

 

1. 

A model aircraft shall be defined as a non-human-carrying device capable of sustained flight in the atmosphere. It shall 
not exceed limitations established in this code and is intended to be used exclusively for recreational or competition 
activity. 

2. 

The maximum takeoff weight of a model aircraft, including fuel, is 55 pounds, except for those flown under the AMA 
Experimental Aircraft Rules. 

3. 

I will abide by this Safety Code and all rules established for the flying site I use. I will not willfully fly my model aircraft in a 
reckless and/or dangerous manner. 

4. 

I will not fly my model aircraft in sanctioned events, air shows, or model demonstrations until it has been proven airworthy. 

5. 

I will not fly my model aircraft higher than approximately 400 feet above ground level, when within three (3) miles of an 
airport without notifying the airport operator. I will yield the right-of-way and avoid flying in the proximity of full-scale 
aircraft, utilizing a spotter when appropriate. 

6. 

I will not fly my model aircraft unless it is identified with my name and address, or AMA number, inside or affixed to the 
outside of the model aircraft. This does not apply to model aircraft flown indoors. 

7. 

I will not operate model aircraft with metal-blade propellers or with gaseous boosts (other than air), nor will I operate 
model aircraft with fuels containing tetranitromethane or hydrazine. 

8. 

I will not operate model aircraft carrying pyrotechnic devices which explode burn, or propel a projectile of any kind. 
Exceptions include Free Flight fuses or devices that burn producing smoke and are securely attached to the model aircraft 
during flight. Rocket motors up to a G-series size may be used, provided they remain firmly attached to the model aircraft 
during flight. Model rockets may be flown in accordance with the National Model Rocketry Safety Code; however, they 
may not be launched from model aircraft. Officially designated AMA Air Show Teams (AST) are authorized to use devices 
and practices as defined within the Air Show Advisory Committee Document. 

9. 

I will not operate my model aircraft while under the influence of alcohol or within eight (8) hours of having consumed 
alcohol. 

10.  I will not operate my model aircraft while using any drug which could adversely affect my ability to safely control my model 

aircraft. 

11.  Children under six (6) years old are only allowed on a flightline or in a flight area as a pilot or while under flight instruction. 
12.  When and where required by rule, helmets must be properly worn and fastened. They must be OSHA, DOT, ANSI, 

SNELL or NOCSAE approved or comply with comparable standards. 

 

RADIO CONTROL 

 

1. 

All model flying shall be conducted in a manner to avoid over flight of unprotected people. 

2. 

I will have completed a successful radio equipment ground-range check before the first flight of a new or repaired model 
aircraft. 

3. 

I will not fly my model aircraft in the presence of spectators until I become a proficient flier, unless I am assisted by an 
experienced pilot. 

4. 

At all flying sites a line must be established, in front of which all flying takes place. Only personnel associated with flying 
the model aircraft are allowed at or in front of the line. In the case of airshows demonstrations straight line must be 
established. An area away from the line must be maintained for spectators. Intentional flying behind the line is prohibited. 

5. 

I will operate my model aircraft using only radio-control frequencies currently allowed by the Federal Communications 
Commission (FCC). Only individuals properly licensed by the FCC are authorized to operate equipment on Amateur Band 
frequencies. 

6. 

I will not knowingly operate my model aircraft within three (3) miles of any preexisting flying site without a frequency-
management agreement. A frequency management agreement may be an  
allocation of frequencies for each site, a day-use agreement between sites, or testing which determines that no 
interference exists. A frequency-management agreement may exist between two or more AMA chartered clubs, AMA 
clubs and individual AMA members, or individual AMA members. Frequency-management agreements, including

 

an 

interference test report if the agreement indicates no interference exists, will be signed by all parties and copies provided 
to AMA Headquarters. 

7. 

With the exception of events flown under official AMA rules, no powered model may be flown outdoors closer than 25 feet 
to any individual, except for the pilot and located at the flightline. 

8. 

Under no circumstances may a pilot or other person touch a model aircraft in flight while it is still under power, except to 
divert it from striking an individual. 

Summary of Contents for WACO YKS-6






























Reviews: