Reference : SGP_AVS_SW_ATLAS-05-05
Classification :
COMPANY
RESTRICTED
Version :
0.17
Project
:
ATLAS_DSW
Status :
Proposed
Chapter
:
User
Manual
Date :
2006-09-12
Section
:
Diagnostic Software (Leco+)
© Philips Electronics N.V. 2006
Philips Semiconductors
Page 10 of 124
1
2.3
COMMAND LINE INTERFACE
2
Via the command line interface the execution of diagnostic nuclei can be controlled.
3
4
2.3.1 Set-up of physical interface components
5
Hardware required:
6
•
Control PC
7
•
One free COM port on the Control PC
8
•
Special cable to connect the DVD Recorder to the Control PC
9
The control PC must use the following port settings for the used COM port:
10
- 19200
bps,
11
- 8
data bits,
12
- n
o parity,
13
- 1
stop bit and
14
- no flow
control.
15
The control PC is connected with a special cable (see chapter 4A.2) to the RS232 port of the
16
DVD Recorder. Via the same connection the ‘test pin’ will be connected to ground. Using this
17
pin the software can determine whether Diagnostic mode needs to be entered.
18
19
2.3.2 Activation
20
After power on the next text will be sent to the control PC
21
22
Factory Diagnostics and Service Software
23
DVD Video Recorder (Dec 13 2003, 10:55:37)
24
25
Version :258 Build :20031213_1030
26
Release :P1_7_b Buildtype :no
27
Baseline :I_P1_8_63 Variant :verum:dvdrw2_lib
28
29
DS:>
30
31
The first lines indicate that the DSW has been activated and contains the version and build info
32
of the DSW. The next line is the command line prompt (“
DS:>
”). The DSW is now ready to
33
receive commands. Please note that this text will be different on your specific variant of the
34
DVD+RW recorder product range.
35
36
2.3.3 Usage
37
The commands that can be given are the numbers of the nuclei. A command must be
38
terminated with an <ENTER> character from the control PC. When typing commands, the
39
backspace key can be used to make corrections. Apart from this one can use the Up and Down
40
arrows to browse to previous commands.
41
When one enters non-supported commands, the interface returns the command line prompt.
42
43
If the command (the nucleus number) is recognised, the nucleus is executed. Result and output
44
of an activated (and terminated) nucleus will be sent back to the control PC.
45
46
Example in case the command is correct:
47
48
DS:> 1200
49
Summary of Contents for DVDR3575H/
