manualshive.com logo in svg

PEUGEOT TSDI, Workshop Manual

Share
Download
PEUGEOT TSDI Workshop Manual Download Page 32

SPECIAL WORK AND PROCEDURES

Page: 32

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

Fuel circuit bleeding procedure 

instruction 2

 

- After refitting the assembly, operate the fuel pump

by turning on the ignition key (turning on the
ignition operates the fuel pump for 3 seconds)
 - Carry out this operation twice

To remove the Injection rail

Imperative: wash the power unit

 - Carry out the procedure used to lower the pressure in
the fuel system (see instruction 1)
 - Remove the clips from the 3 pipes (1 and 2)

(if changed, these clips must not be replaced by
screw-type clips)

 - Disconnect the 2 fuel pipes (1)
 - Disconnect the air pipe (2) from the compressor
 - Remove the injection manifold (3)

 - Remove the O-ring (4) from under the injection
manifold (the O-ring must be renewed each time it is
removed)

Re-assembly: 

Proceed in reverse order to

disassembly and bleed the fuel system (see
instruction 2)

Summary of Contents for TSDI












































Reviews:

No comments

Brands by name

Popular brands

Load more brands