manualshive.com logo in svg

PEUGEOT TSDI, Workshop Manual

Share
Download
PEUGEOT TSDI Workshop Manual Download Page 27

MISCELLANEOUS OPERATIONS

Page: 27

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

MISCELLANEOUS OPERATIONS

To remove the starter system

 - Operate the starter quadrant (1) by hand and
remove the kick start drive gear (2) and its washer

 - Turn the cover over and remove the circlip (3)
with circlip pliers P/N 69117
 - Remove the washer, the starter quadrant (1) and
the spring (4) from the transmission cover

To fit starter system

 

- Fit the return spring (A), with the longest loop on

peg (A) in the cover
 - Fit the starter quadrant (1) into the bearing bush
 - Hook the second loop (B) of the spring onto the
starter quadrant
 - Set the spring so that the starter quadrant is
positioned against its stop (C) in the cover
 - Turn the cover over and fit the washer and circlip
to the quadrant shaft
 - Fit the washer (5) into the ratchet shaft housing
 - Set the quadrant at around 1/8 turn in order to be
able to fit the kick start drive gear
 - Fit the kick start drive gear pin (6) in the cover
housing (D)

Summary of Contents for TSDI












































Reviews:

No comments

Brands by name

Popular brands

Load more brands