manualshive.com logo in svg

PEUGEOT TSDI, Workshop Manual

Share
Download
PEUGEOT TSDI Workshop Manual Download Page 31

SPECIAL WORK AND PROCEDURES

Page: 31

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

Procedure used to lower the pressure in the fuel
system 

instruction 1

Imperative: wash the power unit

 - Remove the saddle/locker assembly
 - Raise the fuel tank in order to with draw the
injection manifold (1) soundproofing.

 - Disconnect the fuel injector (2)
 - Remove the 2 bolts (3) from the injection
manifold (4)
 - Remove the injection manifold without
disconnecting the feed pipes (5)

 - Connect the fuel injector harness tool P/N 756017
to the fuel injector and the battery
 - Put the manifold into a container (6) to catch the
fuel
 - Operate the tool contactor 5 times stopping for 5
seconds between each operation in order to lower
the pressure in the injection manifold feed pipe

,

 Correctly secure the injection rail in the

container as the pressurised fuel jet may be
dangerous for the skin, do not expose the hands
to the petrol jet when the injector is opened

Summary of Contents for TSDI












































Reviews:

No comments

Brands by name

Popular brands

Load more brands