manualshive.com logo in svg

PEUGEOT TSDI, Workshop Manual

Share
Download
PEUGEOT TSDI Workshop Manual Download Page 26

REFITTING SPECIFIC COMPONENTS

Page: 26

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

To fit the injection manifold and compressor

(If they were removed together)

 - Fit the spark plug (1)
 - Fit the temperature sensor (2)
 - Fit the injection manifold (3) (2 bolts) checking
the gaskets are correctly fitted
 - Fit the compressor (4) (4 bolts) with its two
locating dowels and a new 

lightly

 greased O-ring

To fit the drive pulley assembly

 

- Fit the drive pulley with its guide hub onto the

crank
 - Fit the belt (1) to the guide hub
 - Fit the fixed flange (2) to the crank checking it is
properly positioned on the crank splines
 - Fit the nut (3) and tighten finger tight
 - Fit locking tool P/N 755874
 - Tighten the nut with a torque wrench to the
required torque

Note: 

it is forbidden to use a power driver, this

may upset the crank position

Imperative:

 Precautions when refitting the drive

pulley
Certain parts of the drive pulley must not be
discarded or cut down to a smaller size. Any
modifications may cause the nut to tighten against
the crank splines instead of the fixed flange and
damage the crank splines

Summary of Contents for TSDI












































Reviews:

No comments

Brands by name

Popular brands

Load more brands