background image

Owner´s Manual Permobil C350

Safety Instructions

16 

Safety Instructions

Driving with Seat Lift/Seat Tilt/Backrest Recline

 

Be careful in  making sure that nothing gets stuck between the chassis and 

the seat when the seat lift/seat tilt is operated. Operating the seat lift,seat tilt/ 

backrest recline changes the center of gravity and increases the risk of tipping 

over. Always drive in low speed and only use those seat functions on level 

ground, and not on hills, ramps, slopes or other inclines. Using those seat func-

tions while driving on inclines can lead to personal injury and property damage, 

including damage to the wheelchair.

Center of Balance

The possibility of this wheelchair tipping and the point where this wheelchair 

will tip forward, back or to the side depends on its center of balance. Please 

CAUTION that the following factors can affect the wheelchair’s center of bal-

ance:
•  Elevation of the seat

•  Height and angle of the seat

•  Body position or weight distribution

•  Driving on an incline such as a ramp or a hill

•  Use  of  a  backpack  or  other  accessories,  depending  on  the  amount  of 

weight  added.
If  your  wheelchair  begins  to  move  in  an  unexpected  manner,  immediately 

release the joystick to stop the wheelchair. Except in an emergency, do NOT 

use the on/off button to stop your wheelchair, as this will cause the wheelchair 

to stop abruptly and may cause personal injury.

Fixed seat post

Adjusting  the  seat  height  may  only  be  performed  by  an  authorized  service  

provider. See the service manual for more information. 

m

     WARNING

Summary of Contents for C350

















































































































Reviews: