Permobil C350 Owner'S Manual Download

Page: 64 / 112

Owner´s Manual Permobil C350

Handling

Driving - General

Make sure that the control system is mounted securely and that the joystick

position is correct. The body part that you use to operate the joystick should be

supported, for example by the wheelchair arm pad. Do not use the joystick as

the sole support for your hand or limb - wheelchair movements and bumps could

upset your control. Make sure the wheel lock release lever is fully pushed into

the chassis (wheel locks NOT released).

Switch on the power by pressing the start button on the control panel.

2. Choose profile - VR2 Control system

The control system is normaly not programmed with more then one profile,

but in special applications this can occur. In these cases choose a suitible

profile with the profile/maximum speed button, see page 32.

Choose profile - R-net Control system

Choose a suitible profile with the profile button (if the control system is pro-

grammed with more than one profile), see page. 38.

Carefully move the joystick forward to drive forward, and backward to drive

backward.

The speed of the wheelchair is adjusted continuously by the joystick

being moved different distances forward and backward respectively. The

wheelchair’s electronics allow very slow driving over edges. You can drive

up to the edge, and then carefully drive over it.

WARNING

Always make sure your feet are correct and securely positioned on the foot plates before you oper-

ate the wheelchair. Use foot straps if needed. Failure to do this increases the risk of personal injury.

Summary of Contents for C350

















































































































Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands

Permobil C350, Owner'S Manual

Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands