Permobil C350 Owner'S Manual Download

Page: 95 / 112

Owner´s Manual Permobil C350

Maintenance and Repairs

Lift/push the new battery in to the

chassis using the battery strap.

Remount the battery lock.

10.

Connect the battery terminals on

the new battery. Also see the sticker

on the inside of the chassis front

cover.

11.

Remount the front cover.

Changing the batteries

Front battery

Loosen the battery locks by pulling

them straight forward, see figure.

Loosen the battery terminals, see

figure. below. Also see the sticker

on the inside of the chassis front

cover.

Lift/pull the battery out using the

battery strap.

Observe care in the use of metallic objects

when working with batteries. A short-circuit can

easily cause an explosion. Always use protec-

tive gloves and protective eye-glasses.

The batteries are heavy and must be han-

dled with care.

Used or broken drive batteries should be taken

care of in an environmentally correct manner

in accordance with locally applicable recycling

directions.

Pull the battery locks

straight forward.

Battery terminals.

WARNING

Summary of Contents for C350

















































































































Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands

Permobil C350, Owner'S Manual

Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands