Permobil C350 Owner'S Manual Download

Page: 96 / 112

Owner´s Manual Permobil C350

Maintenance and Repairs

Changing the batteries

Rear battery
1.

Place the wheelchair on a level

surface.

Run/fold out the leg support and

raise the seat lift.

Turn off the main power switch on

the control panel.

Put the circuit breaker in the ”OFF”

position. It is accessed through a

hole in the chassis cover; see fig.

Lift the front cover upwards/for-

wards so that the hook and loop

fastener on the inside of the cover

releases, see page 68.

Remove the chassis top cover, it´s

fitted with two knobs, see fig.

Pull the rear cover backwards so

that the hook and loop fastener on

the inside of the cover releases.

Chassis top cover.

Chassis rear cover.

The circuit breaker is accessed

through a hole in the chassis cover.

Off

Summary of Contents for C350

















































































































Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands

Permobil C350, Owner'S Manual

Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands