Permobil C350 Owner'S Manual Download

Page: 80 / 112

Owner´s Manual Permobil C350

Handling

Driving on Sideways Slopes

Driving on a sideways slope must always be performed with great care.
Avoid abrupt avoidance maneuvers and never maintain a speed higher than that

at which you can maneuver the wheelchair in a safe and secure manner.

When driving on sideways slopes with an uneven surface (for example

grass, gravel, sand, ice or snow) a great deal of extra care must be observed.

Do not drive the wheelchair on sideways slopes of greater than 6 degrees. There is a risk of

tipping over.

Operating the seat lift, seat tilt and/or backrest recline changes the center of gravity and increases

the risk of tipping over, hence those seat functions shall only be used on level ground, driving in

low speed with great caution.

Max 6°

WARNING

Summary of Contents for C350

















































































































Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands

Permobil C350, Owner'S Manual

Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands