Permobil C350 Owner'S Manual Download

Page: 103 / 112

Owner´s Manual Permobil C350

Troubleshooting Guide

103

ERROR CODE

POSSIBLE CAUSE - SOLUTION

1 LED - Low battery voltage

Check the battery and the connections between the battery and the control unit.

2 LED - Open circuit, left drive motor

Check the connection to the right drive motor.

3 LED - Short circuit left drive motor

Check the drive motor connections and cable.

4 LED - Open circuit, right drive motor

Check the connection to the right drive motor.

5 LED - Short circuit right drive motor

Check the drive motor connections and cable.

6 LED - Charger connected

Remove the charge plug from the chargesocket on the control panel.

7 LED - Joystickerror

Make sure the joystick isn’t actuated at switch-on, change the control panel.

8 LED - Control System Error

Check the contacts to the power module. If the fault persists, change the poweer module.

9 LED - Failure in wheel lock circuit

Check the connections to the magnetic wheel lock.

10 LED - High battery voltage

Check the battery and the connections between the battery and the control unit.

7+5 LED - Comunication error

Check the control panel cable for damage and make sure the cable connections

aren´t loose.

8+2 LED - Actuator error

If the wheelchair has more then one actuator, check which one is´nt working.

Make sure the cable connections aren´t loose.

Summary of Contents for C350

















































































































Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands

Permobil C350, Owner'S Manual

Search results

Summary of Contents for C350

Reviews:

Related manuals for C350

Brands by name

Popular brands