13
14
G B
GB
2. Press the
EQUALIZER
button repeatedly to select the desired EQ. The displayed
EQ will be effective immediately:
EQ1 Neutral
EQ2 Indoor
EQ3 Outdoor
EQ4 Flat
EQ5 Rock
EQ6 Soul and Jazz
EQ7 Classical
EQ8 Acoustic
EQ9 Dance
EQ10 Spoken word
EQ11 Small room
EQ12 Late night
3. The display will return to normal in 3 seconds, and resume operation.
ADDITIONAL METAL TELESCOPIC ANTENNA
You can use this as an alternative antenna for your radio in areas or locations where the
radio signal (FM/DAB/DAB+) is weak to very weak.
ATTENTION: The standard antenna on the radio is flexible. The metal antenna
is not flexible or bendable and should be used with care. Breaking or bending
antennas is not covered by warranty.
Installing
: Carefully screw off the standard flexible antenna. First carefully loosen the
antenna with an open-end-wrench (size 14) – turn counter anti-clockwise.
Carefully screw on the metal telescopic antenna and softly tighten it with an open-end
wrench key (size 14) – turn clockwise.
ATTENTION: do not use too much force when fixing the antennas as this can
damage the screw threat of the antennas or make it break off.
LANGUAGE SETTING
The menu of the radio can be configured to various languages.
1. Press the
On/Off
button to switch on the radio.
2. Press the
MENU
button, and then rotate the
TUNING
knob until the display shows
“System”.
3. Press the
TUNING
knob; rotate the
TUNING
knob until the display shows
“Language”.
4. Press the
TUNING
knob b to enter the language adjustment menu.
5. Rotate the
TUNING
knob until the desired language appears on the display (default
is English).
6. Press the
TUNING
knob to confirm your choice.
7. The display menu will then change to the chosen language.
SOFTWARE VERSION
The software display cannot be altered and is just for your reference. You can only view
the software version in DAB and FM modes.
1. Press the
On/Off
button to switch on the radio.
2. Press the
SOURCE
button to select FM or DAB mode.
3. Press the
MENU
button and then rotate the
TUNING
knob until the display shows
“System”.
4. Press the
TUNING
knob; rotate the
TUNING
knob until the display shows “SW
version”.
5. Press the
TUNING
knob to view the software version.
6. Press the
MENU
button to return to the normal radio display.
SYSTEM RESET
If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the
On/Off
button to switch on the radio.
2. Press the
MENU
button.
3. Rotate the
TUNING
knob until the display shows “System”. Press the
TUNING
knob.
4. Rotate the
TUNING
knob until the display shows “Factory Reset”. Press the
TUNING
knob.
5. Rotate the
TUNING
knob to select between “Yes” or “No”. Select “Yes” if you wish to
reset the radio, otherwise, select “No”.
6. Press the
TUNING
knob to confirm your choice.
7. A full reset will be performed. All presets and the station list will be erased. All
settings will be set to the default values. The radio will start up and the display
will show “WELCOME TO DIGITAL RADIO” for a few seconds. Then the radio will
automatically perform an auto scan of the Band III DAB channels and the FM band.
The display will show “Scanning” in DAB and “Auto” in FM.
8. When the scan is completed, the 10 strongest FM stations will be stored as presets.
The radio will switch to standby with the updated clock and date showing on the
display.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
reconnect the power supply.
BACKLIGHT
When the radio is in operation or in standby, pressing any button will illuminate the LCD
display for approx. 10 seconds.
