background image

Operation manual 

  turnstile power supply connector block – "XT3" ("

+

12VDC"); 

  remote indicator connector blocks (open/closed, one indicator per each direction) – "XT4" and 

"XT5" ("Light A" and "Light B" accordingly); 

  "J1" connector for turnstile control mode selection (see below); 

  "J2" connector for programming. 

 

Fig. 4 Control Logic Board (CLB) 

5.2.5  Input and output signals and their parameters when operating the turnstile 

The microcontroller set on the CLB processes the incoming commands (i.e. traces the status of 

contacts “Unlock A”, “Stop”, “Unlock B” and “Fire Alarm”), keeps tracing the signals from the arm 

rotation optical sensors and from the intruder detector (contact “Detector”), and sends commands 

to the control mechanism basing on those signals. It also processes signals for the external 

devices: indication on the RC-panel (“Led A”, “Led Stop” and “Led B”), the signal of hub turning in 

the corresponding direction (“PASS 

А

” and “PASS 

В

”), the signal about readiness of the turnstile to 

effect the current command (“Ready”), alarm output signal (“Alarm”) and relays the signal of the 

current status of the intruder detector (“Det Out”). 
The turnstile is operated by input of a low-level signal to the “XT1.L” connector block contacts 

“Unlock A”, “Unlock B” and “Stop” relatively to the “GND” contact. As the control element there can 

be used a normally open relay contact or a circuit with open collector output at that. At the 

emergency unblocking device input the turnstile control is carried out by elimination of a low-level 

signal from the “Fire Alarm” contact relatively to the “GND” contact. As the control element there 

can be used a normally closed relay contact or a circuit with open collector output at that (see 

Fig. 5 and 6). 

 

Note:

 

For generating a high-level signal at all the input contacts (“Unlock A”, “Stop”, “Unlock B”, 

“Fire Alarm” and “Detector”) “2 kOhm” resistors connected to the power supply bus “+ 5V” 

are used. 

The control element provides for the following signal characteristics: 

Relay contact as the control element: 

minimum switched current  ...........................................................................................  2 mA 

closed contact resistance 

(considering resistance of the connected cable) .............................................  max 300 Ohm 

Circuit with open-collector output as the control element: 

voltage at closed contact (low - level signal at the CLB input) ................................  max 0.8V 

Summary of Contents for TTD-03.1































Reviews: