manualshive.com logo in svg

Pepperl+Fuchs IC-KP-B7-V95, Manual

Share
Download
Pepperl+Fuchs IC-KP-B7-V95 Manual Download Page 8

 20

13

-0

4

8

IC-KP-B7-V95

Safety

3

Safety

3.1

Symbols relevant to safety

3.2

Intended use

The IDENTControl IC-KP-B7-V95 is a control interface including a DeviceNet 

interface for identification systems. The device can be used as a control cabinet 

module or for field applications. Besides the DeviceNet connection, suitable 

inductive R/W heads, microwave antennas or trigger sensors can be connected. 

Wiring suitable for the system design must be used.

3.3

General notes on safety

Only instructed specialist staff may operate the device in accordance with the 

operating manual.

User modification and or repair are dangerous and will void the warranty and 

exclude the manufacturer from any liability. If serious faults occur, stop using the 

device. Secure the device against inadvertent operation. In the event of repairs, 

return the device to your local Fuchs representative or sales office. 

The connection of the device and maintenance work when live may only be 

carried out by a qualified electrical specialist. 

The operating company bears responsibility for observing locally applicable 

safety regulations.

Store the not used device in the original packaging. This offers the device optimal 

protection against impact and moisture.

Ensure that the ambient conditions comply with regulations.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt devices and any connected facilities or systems, 

or result in their complete failure.

Summary of Contents for IC-KP-B7-V95



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands