manualshive.com logo in svg

Pepperl+Fuchs IC-KP-B7-V95, Manual

Share
Download
Pepperl+Fuchs IC-KP-B7-V95 Manual Download Page 17

IC-KP-B7-V95

Installation

 20

13

-0

4

17

5.4.2

Read/Write Head and Trigger Sensors

A maximum of 4 read/write heads can be connected to the IDENTControl.

Instead of the read/write heads, a maximum of 2 trigger sensors can be 

connected to sockets 3 and 4. A trigger sensor can be assigned to only one 

read/write head. The trigger sensors must be PNP.

Connect the read/write heads and trigger sensors to the sockets on the top of the 

enclosure using M12 connectors.

For details of compatible read/write heads,  and of compatible connecting cables, 

see chapter 4.7.1.

5.4.3

Cable length between control interface and R/W heads

The maximum cable length between the control interface and a connected R/W 

head is 1000 meters. If you wish to attain the maximum possible cable length, 

select a suitably large cable cross-section. See chapter 4.7.1

5.4.4

Ground connection

The ground connection of the IDENTControl is located at the lower right of the 

connector array. The ground conductor is screwed to the housing with a crimp 

connector. In order to guarantee safe grounding, the serrated washer must be 

mounted between the crimp connector and the housing.

A cross-section of at least 4 mm

2

 is recommended for the ground conductor lead.

trigger switch

trigger sensor

read/write head

signal

socket at housing

2

1

3

4

5

+

A

-

+

-

B

1

2

3

4

5

1

Housing

2

Serrated lock washer

3

Crimp connector

4

Lock screw

1

2

4

3

Summary of Contents for IC-KP-B7-V95



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands