manualshive.com logo in svg

Pepperl+Fuchs IC-KP-B7-V95, Manual

Share
Download
Pepperl+Fuchs IC-KP-B7-V95 Manual Download Page 30

 20

13

-0

4

30

IC-KP-B7-V95

Commands

Confirmation

Response: Type IPC03 tag is located in front of the read/write head, the 

highlighted part depends on the content of the tag

Alternative response: No tag in front of read/write head

7.3

Command types

When using commands, a distinction is always made between the two command 

types 

single mode

 and 

enhanced mode

.

Single mode

The command is executed once. A response is issued immediately.

Enhanced mode

The command remains permanently active until it is interrupted by the user or by 

an error message. A response is issued immediately.

The command remains active after the response is issued. Data is only 

transferred if read/write tags change. Read/write tags are not read twice. If a 

read/write tag leaves the read range, the status '5' is output.

10:22:FF:01
10

Repeat command code 

SR

 (single read words)

22

Number of double words (2) / channel (1), toggle bit

FF

Status FFh (processing command)

01

Reply counter

10:22:00:02:

31:32:33:34:35:36:37:38

10

Repeat command code 

SR

 (single read words)

22

Number of double words (2) / channel (1), toggle bit

00

Status 0 (command executed without error)

02

Reply counter

31:32:33:34:35:36:37:38 Data

10:02:05:02
10

Repeat command code 

SR

 (single read words)

02

Number of double words (0) / channel (1), toggle bit

05

Status 5 (no tag in the detection range)

02

Reply counter

Summary of Contents for IC-KP-B7-V95



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands