Pentair 3200NXT, Service Manual

Page: 9 / 36

Page 9
Master Programming Mode Flow Chart
Entering Master Programming Mode:
Press and hold the Shift and Up buttons for 5 seconds. 1.
Press the Extra Cycle button once per display until all displays are viewed and Normal Display is resumed.Option setting
displays may be changed as required by pressing either the Up or Down button. Use the Shift button to move one space
to the left.
Depending on current valve programming, certain displays may not be viewed or set.
2.
NOTE: If the “D” button is pressed while in master programming, no changes will be saved.
CAUTION: Before entering Master Programming, please contact your local professional water dealer.
SYSTEM TYPE: 4
SINGLE UNIT
Options: System 4 (single unit)
System 5 (2-4 units)
System 6 (2-4 units)
System 7 (2 units)
System 9 (2-4 units)
VALVE ADDRESS:
#2
Options: Valve Address #1 (First Control Valve)
Valve Address #2 (Second Control Valve) (Default)
Valve Address #3 (Third Control Valve)
Valve Address #4 (Fourth Control Valve)
Example:
System Type 4, Single Unit
Example:
Valve Address #2 (Second Control Valve) (Default)
SYSTEM SIZE:
2 VALVES
Options: 2 Valves in the System (Default)
3 Valves in the System
4 Valves in the System
Range: 2 to 4 Valves in the System
Example:
2 Valves in the System (Default)
REGEN TRIGGER:
TIME CLK DELAYED
Options: Time Clock Delayed (System 4 Only) (Default)
Meter Immediate (All System Types)
Meter Delayed Fixed Reserve (Systems 4 & 6 Only)
Remote Signal Start Immediate (All System Types)
Example:
Time Clock Delayed (Default)
VALVE TYPE:
2750
Options: 2750 (Default)
2850
2900
3150
3900
Stager - Butterfly
Stager - Notch Cam
Example:
2750 (Default)
NOTE: This screen will not display for
System Type 4.
NOTE: This screen will not display for
System Type 4.
NOTE: This screen will only display on
the lead unit for System Types 6 & 7.
For all other System Types, it will display
for all units.
REGENERANT FLOW:
DOWNFLOW
Options: Downflow (Default)
UF Brine Draw
UF Fill First
Example:
Downflow (Default)
REMOTE SIGNAL
START: 00:06:00
Options: 00:06:00 (Default)
Range: 1 second to 99 minutes (1 hour, 39 minutes)
Example:
06:00:00 (Default)
(Hours:Minutes:Seconds)
DISPLAY FORMAT:
US-GALLONS
Options: U.S. - Gallons (Default)
European Units - Cubic Meters (Metric)
NOTE: In U.S. - Gallons mode, the display will be in 12-hour time.
NOTE: In European Units - Cubic Meters (Metric) mode, the display will
be in 24-hour time.
Example:
U.S. Gallons (Default)
UNIT CAPACITY:
00000000 GRAINS
Options: Grains (in U.S. Format) (Default)
Degrees (in Metric Format)
Range: 9,000 to 9,900,000 Grain Capacity in U.S. Format
90.0 to 190,000 Degree Capacity in Metric Format
NOTE: The word “GRAINS” will change to “DEGREES” in the metric
Display Format. Use the Shift button to move to the left.
Example:
Grains (Default)
CAPACITY SAFETY
FACTOR: 00%
Range: 0 to 50%
NOTE: Use the Shift button to move to the left.
Example:
00% (Default)
FEED WATER
HARDNESS: 15 GPG
Range: 1 to 199 Grains/Gallon (U.S. Format)
2 to 199 Degrees (Metric Format)
NOTE: Use the Shift button to move to the left.
Example:
15 GPG (U.S. Format)
(Default)
REGENERATION DAY
OVERRIDE:OFF
Example:
Off (Default)
REGENERATION DAY
OVERRIDE:01 DAYS
Options: Off (Default) or On
Range: 1 to 99 Days
Example:
1 Day
CYCLE 1 00:00:00
BACK WASH
Example:
Cycle 1 in Back Wash Mode
Options: Regeneration Cycle Step #1
Regeneration Cycle Step #2
Regeneration Cycle Step #3
Regeneration Cycle Step #4
Regeneration Cycle Step #5
NOTE: Please refer to the “Regenerant Flow Default Cycle Steps & Times”
in the Master Programming Mode section of the manual.
AUXILIARY RELAY:
DISABLED
Example:
Auxiliary Relay is Disabled
Options: Enabled
Disabled (Default)
CHEMICAL PUMP:
DISABLED
Example:
Chemical Pump is Disabled
Options: Enabled
Disabled (Default)
CPO AUX RELAY
VOLUME: 000 g
Example:
Chemical Pump Auxiliary Relay
Volume at 0 Gallons
Range: 000 to 999 gallons in U.S. Format
0.000 to 9.999 m3 in Metric Format
CPO AUX RELAY
TIME: 00:00:00
Example:
Chemical Pump Auxiliary Relay at 0 Hours,
0 Minutes, & 0 Seconds
Range: 00:00:00 to 02:00:00
FLOW METER:
1.0 PADDLE
Example:
1.0 Paddle Flow Meter
Options: 1.0 Paddle
1.0 Turbine
1.5 Paddle
1.5 Turbine
2.0 Paddle
3.0 Paddle
Generic
MAXIMUM FLOW
RATE: 0000 gpm
Example:
Maximum Flow Rate of 0 gpm
Range: 20 - 2,000 gpm (U.S. Format)
2.0 - 200.0 m3 (Metric Format)
Range: 1 - 99 Gallons (U.S. Format)
0.1 - 09.9 M3 (Metric Format)
Pulses: 1 - 99
PROGRAMMING UNIT
PLEASE WAIT...
Example:
Master Programming Mode is Exiting
REGENERATION
TIME: 02:00AM
Example:
2:00 A.M. (Default)
Options: A.M. (U.S. Format)
HR (Metric Format)
NOTE: Regeneration time will not appear unless
Regeneration Day Override is on.
Options:
Gallons (U.S. Format)
Meter3 (Metric Format)
ADD 01 GALLONS
EVERY 001 PULSES
Example:
Add 1 Gallon for Each Pulse in U.S. Format
AUX RELAY OUTPUT
START 1 00:00:00
Example:
Auxiliary Relay Output in Start 1 at
0 hours, 0 minutes, & 0 seconds
Range: 00:00:00 to 18:00:00
AUX RELAY OUTPUT
END 1 00:00:00
Example:
Auxiliary Relay Output in End 1 at
0 hours, 0 minutes, & 0 seconds
Range: 00:00:00 to 18:00:00
NOTE: Only displayed if Auxiliary
Relay is enabled in previous screen.
Auxiliary Relay will only display if
Chemical Pump is OFF for System
Types 6 & 7.
NOTE: If Stager is chosen for Valve
Type, the Regeneration Cycle Step
description will not display.
NOTE: Only displayed on units that
physically have a meter (Lead
always has a meter). Only shown if
Auxiliary Relay is disabled on
System Types 6 & 7.
NOTES: Default flow meter type is
based on the valve type. This screen
will only display on the lead unit for
System Types 6 & 7. All other system
types it will display for all units.
NOTE: Only displayed if “Generic”
is chosen for the flow meter.
NOTE: Only displayed if “Generic”
is chosen for the flow meter.
NOTE: This screen will only display on
the lead unit for System Types 6 & 7.
For all other System Types, it will display
for all units.
NOTE: Depending on current option settings, some displays cannot be viewed or set.