Pelsue 500964-001 Product Manual Download Page 15

Page: 15 / 20

#500964-001 -

Product Manual: Model #SB-SM1 Fall Arrest Tower Base

- Revision 01 - Date: 03-04-2010

Page 15

5.2 - Product Installation & Set-up (continued)

3. Installation of a #FT-C70 Fall Arrest Tower on the #SB-SM1 4-Arm Manway Mount

Install the #SB-SM1 4-Arm Manway Mount per the instructions in Step #2 of section 5.2 of this manual.

After the #SB-SM1 has been completely installed, remove the pin from the base of the fall arrest tower.

Place the fall arrest tower onto the #SB-SM1, center the base of the tower between the base lugs present on the

manway mount (Refer to Fig. 5.2f).

Align the holes of the fall arrest tower base with the holes of the base lugs on the #SB-SM1 and replace the tower’s

retaining pin (Refer to Fig. 5.2g).

Adjust the leveling pegs in order to make the tower vertical (Refer to Fig. 5.2g).

! WARNING !

- The #FT-C70 fall

arrest tower can only be used for the anchoring of personal fall arrest systems when placed in a vertical position!

Utilize the installed fall arrest tower within the limits of and according to the instructions provided within the Model

#FT-C70 fall arrest tower’s product manual.

Figure #5.2h:

#SB-SM1 & FT-C70

Completely Installed

Figure #5.2f:

#SB-SM1 & FT-C70

Installation

!WARNING!

- The FT-C70 Fall Arrest Tower utilized in

conjunction with the #SB-SM1 4-Arm Manway Mount must

be installed according to its product manual, and utilized

by a qualified individual in order to retain its stated rating

& compliance.

!WARNING!

- Any FT-C70 Fall Arrest Tower attached to the

#SB-SM1 4-Arm Manway Mount must be utilized within its

published limits and capabilities. The rating of the installed

tower may supersede or derate the capabilities of the #SB-

SM1 manway mount.

!WARNING!

- The maximum number of connected users permitted on the Model

#FT-C70 tower will be reduced to “2” when utilized in conjunction with the Model

#SB-SM1 tower base. Each connection to the tower must be made via a 900 LB.

MAF (Maximum Arrest Force) device.

Figure #5.2g:

#SB-SM1 & FT-C70

Installation

Leveling

Pegs

Hitch

Base

Lugs

Summary of Contents for 500964-001





















Search results

Summary of Contents for 500964-001

Reviews:

Related manuals for 500964-001

Brands by name

Popular brands

Pelsue 500964-001, Product Manual

Search results

Summary of Contents for 500964-001

Reviews:

Related manuals for 500964-001

Brands by name

Popular brands