manualshive.com logo in svg

Patton ipRocketLink 3101 Series, Getting Started Manual, Page: 81 / 119

Share
Download
Patton ipRocketLink 3101 Series Getting Started Manual Download Page 81

Interface Grouping Setup

81

Model 3101 Series Getting Started Guide 

5 • Advanced Configuration

Interface Grouping Setup

Click 

Advanced Setup > Interface Grouping 

to configure mapping groups. 

Figure 102. WMI: Interface Grouping Entries

Interface grouping supports multiple ports to PVC and bridging groups. Each group will perform as an inde-
pendent network. To support this feature, you must create mapping groups with the appropriate LAN and 
WAN interfaces using the 

Add

 button. The 

Remove

 button will delete the grouping and add the ungrouped 

interfaces to the default group. Only the default group has IP interface. 

Click the 

Add

 button to display the 

Interface Grouping Configuration 

page (

Figure 103 

on page 82). Follow 

the on-screen configuration steps to configure the parameters of the interface grouping. Click 

Apply/Save

 to 

apply the settings.

Summary of Contents for ipRocketLink 3101 Series
























































































































Reviews:

No comments