manualshive.com logo in svg

Patton ipRocketLink 3101 Series, Getting Started Manual, Page: 43 / 119

Share
Download
Patton ipRocketLink 3101 Series Getting Started Manual Download Page 43

WAN Service Setup

43

Model 3101 Series Getting Started Guide 

5 • Advanced Configuration

–

Use Static IPv6 Address:

 If enabled, the 3101 uses this IP as the WAN IP address. If disabled, the 3101 

obtains an IP address assigned through uplink equipment. 

–

Enable IPv6 Unnumbered Model:

 Enable or disable this function.

– Enable PPP Debug Mode: 

Enable or disable this function.

–

Bridge PPPoE Frames Between WAN and Local Ports: 

Enable or disable this function.

–

Enable IGMP Multicast Proxy: 

Enable this function if you want PPPoE mode to support IPTV.

–

Enable MLD Multicast Proxy: 

Enable or disable this function.

Click 

Next

 to continue.

4.

On the 

Routing-Default Gateway 

page (

Figure 25

), select a preferred WAN interface as the system default 

gateway. Click 

Next

 to continue. 

Figure 25. WMI: Routing - Default Gateway

Summary of Contents for ipRocketLink 3101 Series
























































































































Reviews:

No comments