Patron TOM 5, Information For Use

Page: 6 / 36

6
−
Always apply the parking brakes, when getting in and out the stroller.
−
The stroller is not designed to by driven down the stairs.
−
Ensure yourself that the fixing accessories, safety bar and other equipment is fitted and adjusted correctly.
−
Do not stand on the footrest.
−
The brakes must be engaged at all times when the stroller is not moving.
−
Getting over the curb practice firstly with an empty stroller.
−
The attendant must take precautions against the fire risk. In buildings, check the location of fire exits and ensure
procedures are understood.
−
Do not let children play with or hang on the stroller.
−
During the drive keep full attention, to avoid any dangerous situation or collisions.
−
Do not overload the stroller. Overloading of a chassis, seat, bag or basket causes reduction of stability of the
stroller.
−
Make the full attention, when manipulate with the stroller, not to injure the child or yourself.
−
If it is possible, always use drive - up ramps or lift to overcome any access restrictions.
−
Always lift the stroller in two persons.
−
Never transport the stroller when you and/or assistance are not sure if you can transport the stroller with the child
safely.
−
When you drive the stroller on the road, follow the road traffic regulations.
−
Do not use the stroller for any other purposes then it is designed for.
−
The stroller is designed to carry only one child.
−
Do not use any other than original PATRON accessories designed for this product.
−
When the stroller is folded and unfolded, the user guide must be followed carefully, to avoid any damage on the
construction what could affect the product stability.
−
In case of apparent defect, which limits product ’ s safe using (e.g. damage of chassis, part falls away or other
optically visible defects, cracks etc.) it is necessary to stop using the product immediately and contact your local
official distributor or service centre.
−
Company PATRON does not bear any responsibility for the damages caused by using other than original PA-
TRON accessories supplied by this company.
−
Company PATRON does not bear any responsibility for the damages and accidents caused by inappropriate use
of this product.
PREPARATION FOR USE, USE:
1) Chassis:
Assembling the stroller (with attached seat):
Place folded stroller on wheels. Unbutton and release the transport safety - catch on frame. To open the undercarriage
stay between the rear wheels and hold handle tightly. Move handle up and backwards until the handle folding re-
lease is fully locked in its end position. To check the locking position, move upwards the handle to ensure that both
mechanism are fully locked (the undercarriage must not start folding). Pull the seat tilt - in - space adjustment lever
(pic.5) and move the seat to the requested position. Pull the padded frame covers downwards over the locking
mechanism and close both covers by zippers properly .Release backrest recline adjustment lever and set the position
of backrest. Tighten lever properly. Release the footrest angle adjustment lever, set the position of footrest and
tighten lever again. Unfold the footplate and lock it by velcro fastener. Attach the safety bar. Attach and adjust
fixation accessories if needed. The stroller is assembled.
Folding the stroller (with attached seat):
Apply the parking brake and take off the safety bar. Release the footrest angle adjustment lever, set the position of
footrest a bit less than horizontally, ca. 20 degrees (pic.4). Release the footrest velcro lock and close the footplate
(pic.4). Release the backrest recline adjustment lever and push backrest as far as possible forward, towards the seat
base. (It is recommended to take out the exceeding fixing accessories and adjust the seat width by side plates to the
maximum limit, which enables to decrease the size of the folded seat). Tighten the lever. Unzip the padded frame
covers partially and pull over the locking mechanism upwards. Pull the seat tilt - in - space adjustment lever (pic.5)
and set the position of the seat to tilt forward to maximum (pic.6). Lift the handle folding release movable parts
(pic.6) on both sides and fold the handle forward towards the front wheels. Ensure folded undercarriage by
transport safety - catch. The stroller is folded (pic.7).
Assembling and disassembling the undercarriage:
Folding - Apply the parking brake. Unzip the padded frame covers partly and pull over the locking mechanism
upwards. Lift the handle folding release movable part (pic.5) and fold the handle forward towards the front wheels.
Ensure folded undercarriage by transport safety - catch. The undercarriage is folded (pic.7).
Assembling – use the same procedure, but start from the end of instruction above.
Chassis - and - Seat Interface (CSI):
Taking off the seat:
Apply the brake. Release the interface lock safety pin (pic.9) and hold it. Simultaneously pull (pic.10) and unlock
the seat interface locking release (pic.8). Lift the seat.