Patron TOM 5, Information For Use

Page: 7 / 36

7
Fitting the seat in the driving direction
Place the seat exactly into frame seat fittings. FIRSTLY always start to insert just a side of the seat into the FREE
interface socket (without locking pins). By pushing down the second side, the seat will be locked automatically (you
will hear the locking sound). Finally check the seat proper locking by slight lifting of the seat unit. Seat must not
separate from the interface frame.
Fitting the seat against the driving direction:
To place the seat against the driving direction follow the same procedure like in previous chapter except of turning
the seat 180° to be facing backside to front.
Parking Brake:
To brake the wheels press fully the brake connecting rod. To disengage the parking brake lift fully the brake con-
necting rod. (pic.9).
Swivel lock:
If needed, the front wheel forks can be locked against vertical rotation. To lock the castor forks lift and turn the
swivel lock pin by 90° on both sides (pic.15) and let it to snap in in the designated hole on the castor fork (pic.10).
Handle height adjustment:
To change the handle height position press the black plastic buttons on the handle hinges on both sides simultane-
ously (pic.2), set the handle to desired position, release buttons. Handle will lock in new position automatically, you
will hear the locking sound.
Safety Bar:
To take off the safety bar (pic.12) press pin release on both sides simultaneously and pull the bar upwards to remove
it. To insert the safety bar, both pin releases have to be pointed ahead. Press slightly both press pins and insert the
safety bar into the tube inlays at once until the pins are locked. Check the correct position of safety bar by slight
pulling up, safety bar must not lift.
2) Seat - unit positioning and adjusting::
Seat - unit tilt - in - space positioning:
Unzip the right padded frame cover partially from bottom upwards to be able to touch the reclining lever (pic.5).
Hold the seat backrest firmly by left hand. Pull by right hand the seat tilt - in - space lever and set the position of the
seat (pic.5). Release the lever and close the zipper of padded frame cover fully till the lower end.
Seat depth adjustment:
Strip off the seat base upholstery from the seat base (attached by velcro fasteners). Loosen two hexagon - bolts
placed under the frontal middle part of seat by wrench key (21, pic.2). Wrench key is placed in backrest rear pocket.
Loosen by hand 4 plastic nuts placed under the seat (19, pic.2). Set the desire depth - size of the seat by pulling or
pushing. Properly tighten all hexagon - bolts and plastic nuts and place back the seat base upholstery.
Seat - base width adjustment:
Take off the seat base upholstery from the side plates. Loosen by hand 4 adjusting plastic nuts placed under the seat
(19, pic.2). Set the seat width by pulling or pushing of the side plates. Properly tighten all plastic nuts and cover
back the side panels by upholstery.
Backrest recline positioning:
Hold the seat backrest firmly. Loose backrest recline adjustment lever (7, pic.1 and 3). Set the position of backrest.
Tighten the lever properly. If needed unzip partially the zipper placed on the rear part of backrest cover to make the
manipulation easier. Check the correct locking of the backrest position. Backrest must stay in preset position.
Backrest height adjustment:
Strip off the backrest upholstery from the rear and front side of the backrest (attached by velcro fasteners). Loosen
two hexagon - bolts placed on top part of backrest rear side (5, pic.3). Loosen two plastic nuts on the rear side of
backrest (6, pic.1 and 3). Set the height of the backrest by lifting or pressing down. Properly tighten all hexagon -
bolts and plastic nuts and place back the backrest upholstery.
Footrest set angle positioning:
Hold the footrest firmly. Release the footrest angle adjustment lever (20, pic.2). Set the angle of footrest set. Tight-
en properly the lever to fix its position.
Footrest - set height positioning:
Loosen two hexagon - bolts placed on rear side of footrest slider profile (22, obr.1). Set desired position of footrest.
Properly tighten both hexagon - bolts.
Footplate angle adjustment:
Loosen two hexagon - bolts placed under the footplates (23, pic.11). Set the angle of footplate by pulling or pushing
of footplate angle adjustment slide - plate (24, pic.11), which is determine requested angle of the footplate. Properly
tighten both hexagon - bolts.
Footplate velcro lock:
Tighten and fasten at any time the velcro lock fastener placed under the footplate (25, pic.11) to ensure fixed foot-
rest position. (security device against folding of footplate).
3) Stroller in operation:
Getting into the stroller:
Engage parking brake. If necessary ask trustful person for help to hold the stroller firmly. Place the child into the