
SERIE AX8000
11
CONNECTIONS
3
CONNESSIONI
Calcolo del numero di diffusori (tramite le potenze)
Si supponga di avere definito sia l'amplificatore (cioè la sua potenza di
uscita) che il tipo di diffusore con relativa potenza assorbita.
In questo caso il massimo numero di diffusori collegabile sulla linea è
determinato dalla seguente formula:
Esempio
: si utilizzino un amplificatore
AX8240
con plafoniere modello
Paso C42
. L'amplificatore è in grado di erogare una potenza pari a
240 W, mentre un diffusore assorbe una potenza di 6 W.
Per sapere quanti diffusori sono collegabili alla linea di uscita si calcola:
Calcolo del numero di diffusori (tramite le impedenze)
Se il dato disponibile è l'impedenza del diffusore, il numero massimo di
diffusori collegabili ad una linea è:
240 W
6 W
numero diffusori
=
=
40
numero diffusori
=
potenza amplificatore
potenza diffusore
numero diffusori
=
impedenza diffusore
impedenza amplificatore
dove l'impedenza nominale dell'amplificatore è ricavabile dalla
tabella 3.8.1.
Esempio
: si utilizzino un amplificatore
AX8240
con diffusori tipo
Paso C55
, che presentano una impedenza pari a 500 ohm.
Dalla tabella 3.8.1 si trova che l'impedenza nominale di carico della linea
a 100 V è pari a 41,7 ohm.
Quindi:
500
Ω
41,7
Ω
numero diffusori
=
=
12
3.9 PRESA EQUALIZZATORE
Nei casi in cui fosse richiesta una correzione acustica del segnale, è
possibile collegare un equalizzatore all'amplificatore tramite le prese
POWER IN
e
PRE OUT
[
14
]. Per l'inserzione dell'equalizzatore,
l'interrutore
LINK
posto sul retro dell'apparecchio non deve essere
nella posizione
ON
. Questa realizzazione permette la correzione acustica
di ambienti particolarmente riverberanti e la soppressione della
retroazione acustica diffusore-microfono (effetto Larsen).
Se all'amplificatore non sono collegate, tramite le prese
POWER IN
e
PRE OUT
, altre apparecchiature, l'interruttore
LINK
deve essere posto
in posizione
ON
.
Determining the number of speakers (through power values)
If both the amplifier (i.e. its output power) and the type of speaker
with its power consumption have been established, the maximum number
of speakers which may be connected to the line may be determined as
follows:
number of speakers
=
amplifier power
speaker power
Example
: in a system including a
AX8240
amplifier with ceiling speakers
type
Paso C42
is used, the amplifier can supply 240 W power whereas
the speaker has a power consumption of 6 W. The number of speakers
which may be connected to the output line is given by the following:
240 W
6 W
number of speakers
=
=
40
Determining the number of speakers (through impedance)
If the impedance of the speaker is known, the maximum number of
speakers which may be connected to the line is:
number of speakers
=
speaker impedance
amplifier impedance
where the amplifier rated impedance may be determined referring to
Table 3.8.1.
Example
: If a
AX8240
amplifier is used with speakers type
Paso C55
having a 500 ohm impedance, the rated load impedance of the line at
100 V may be determined from Table 3.8.1 as being equal to 41,7 ohm.
Thus:
500
Ω
41,7
Ω
number of speakers
=
=
12
3.9 EQUALIZER SOCKET
If a signal sound adjustment is required an equalizer may be connected
to the amplifier through the
POWER IN
and
PRE OUT
sockets [
14
].
To activate the equalizer, make sure that the
LINK
switch on the back
of the unit is not set to
ON
. This set-up makes possible the sound
adjustment for highly reverberating environments as well as for the
sound adjustment for highly reverberating environments as well as for
the suppression of the acoustic feedback between the speaker and the
microphone (Larsen effect). If no other device is connected to the
amplifier through the
POWER IN
and
PREOUT
sockets, the
LINK
switch
must be set to
ON
.
Fig. 3.9.1
11-528.p65
08/06/01, 14.20
11