background image

- 11 - 

 

 

 

5

) – READ KEY: (MEASUREMENT READINGS)

 

The ‘READ’ Key will scroll through each system measurement. 
 

(6) – SETTINGS KEY:

 

(PROCESS VALUES)

 

The ‘SETTINGS’ Key will scroll through each user setting (process value).  The amber LED will illuminate 
indicating the display is active. 
 

(7) – YES / UP KEY:

 

(YES & UP)

 

When the ‘YES / UP’ Key is pressed, the controller will either increment up or toggle depending on which 
user setting is selected in the ‘SETTINGS menu.  Note the SETTINGS Key amber LED will now flash.  To 
save the ‘new’ process value setting, press the SETTINGS Key again – a message ‘ARE YOU SURE?’ will 
display (answer either YES or NO, the LED will stop flashing. 
 

(8) – NO / DOWN KEY:

 

(NO & DOWN)

 

When the ‘NO / DOWN’ Key is pressed, the controller will either decrement up or toggle depending on which 
user setting is selected in the ‘SETTINGS menu.  Note the SETTINGS Key amber LED will now flash.  To 
save the ‘new’ process value setting, press the SETTINGS Key again – a message ‘ARE YOU SURE?’ will 
display (answer either YES or NO, the LED will stop flashing. 
 

(9) – MULTI COLORS INDICATOR:

  

These LED’s will illuminate in RED, AMBER and GREEN.  They represent a ‘visual’ indication as to dryer 
loading.  If all the LED’s are RED, this is the worst possible state (a combination of very bad dew point and or 
overloaded.  The other side of the spectrum would be only one GREEN LED illuminated; indicating less then 
(<10%) ten percent capacity is being utilized and all is OK.  
 

(10) – MAINTENANCE MONITOR:

 

The controller will remind the user to perform maintenance on the dryer every six month.  The Display will 
indicate (and the ALARM LED will flash), the statement “CHANGE FILTER.”  IMPORTANT – The user 
should change the coalescing filter on a regular basis.  Also do all other recommended maintenance (see 
maintenance section of the Operating Manual) at this time.  
 
To reset the ‘Maintenance Monitor’ at the completion of the maintenance procedures, push the ALARM Key 
and when the “HAS FILTER BEEN CHANGED? (YES / NO)” message is in the Display, press the ‘YES’ Key.  
Pressing the YES Key will reset the Change Filter timing for six months.  Selecting the ‘NO’ key will exit the 
menu and the message will repair again in 8 hours. 
 
 

OTHER FEATURES:

  

On ‘power-up’ the Display will indicate the system configuration (System Operating Code #, CFM Range and 
Firmware Revision) for three seconds. 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Airtek SMART CYCLE PLUS 100














































Reviews: