background image

52

   

Reference & Installation Manual 

  

12.31 Personal Reporting Delay    

Section 

[836]

: Communication Timers

000 to 255 times, Max. 127, Default = 5

When using the Personal Reporting Format, the control panel will wait for the Personal Delay period before transmitting the 
report codes. This is to allow time for the system to provide a dial tone or to bypass the “welcome” message before sending data. 

This section applies to the Plug-in Voice Dialer when using a VDMP3.

12.32 Personal Reporting Message Repetition    

Section 

[837]

: Communication Timers

000 to 255 times, Max. 10, Default = 3

When using the Personal Reporting Format, the control panel will repeatedly send the report codes to the pager until the 
transmission has been acknowledged. 

This section applies to the Plug-in Voice Dialer when using a VDMP3.

12.33 Disable Reporting

Sections 

[800]

 

Option [1] OFF = Dialer Activated (default)
Option [1] ON

= No Dialer

With this option disabled (default), the control panel will continue to report events. With the option enabled, reporting is disabled. 

Summary of Contents for Magellan MG5050 EN






































































Reviews: